ELECTRONICALLY CONTROLLED BRAKE SYSTEM, Diagnostic DTC:C1345/66, C1368/67

DTC Code DTC Name
C1345/66 Linear Solenoid Valve Offset Learning Undone
C1368/67 Linear Solenoid Valve Offset Malfunction

DESCRIPTION

The skid control ECU assembly stores and corrects the individual differences in the brake pedal stroke sensor assembly, actuator solenoids, and stroke simulator solenoid. Perform initialization and calibration of the linear solenoid valve if any of these parts is replaced.

These DTCs are cleared when the linear valve offset learning results are normal.

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1345/66 Linear Solenoid Valve Offset Learning Undone

501

502

503

504

Linear valve offset learning undone.


  • INF Code: 501


    • Linear valve offset learning for front wheel RH is undone.


  • INF Code: 502


    • Linear valve offset learning for front wheel LH is undone.


  • INF Code: 503


    • Linear valve offset learning for rear wheel RH is undone.


  • INF Code: 504


    • Linear valve offset learning for rear wheel LH is undone.

 Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal. Electronically controlled brake system DTC
C1368/67 Linear Solenoid Valve Offset Malfunction 505 Offset learned value out of specification.

  • Perform linear valve offset learning and check for DTCs. If no DTCs are output again, the valve is normal.

  • Brake actuator assembly

 Electronically controlled brake system DTC
DTC No. Brake warning light / yellow (minor malfunction) code ABS warning light code Slip indicator light code Brake hold standby indicator light code
C1345 66 42 45 21
C1368 67 42 45 21

CAUTION / NOTICE / HINT

Note

When replacing the brake actuator assembly, perform initialization and calibration of the linear solenoid valve.

Click here

PROCEDURE


  1. CHECK DTC


    1. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    2. Turn the engine switch off.

    3. Turn the engine switch on (IG).

    4. Check the DTCs (electronically controlled brake system and SFI system) that are output.

      for Electronically Controlled Brake System: Click here

      for 2UR-GSE (w/ Canister Pump Module): Click here

      for 2UR-GSE (w/o Canister Pump Module): Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs (except C1345/66, C1368/67 and SFI system DTCs) are not output. A
      SFI system DTCs are output. B
      DTCs (except C1345/66 and/or C1368/67) are output. C

      Tech Tips

      Before performing initialization and calibration of the linear solenoid valve, C1203/95 will be output.


    B

    INSPECT SFI SYSTEM for 2UR-GSE (w/ Canister Pump Module): Click here
    INSPECT SFI SYSTEM for 2UR-GSE (w/o Canister Pump Module): Click here

    C

    REPAIR CIRCUITS INDICATED BY OUTPUT DTCS Click here

    A

  2. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE


    1. Turn the engine switch off.

    2. Perform initialization and calibration of the linear solenoid valve.

      Click here


      Chassis > ABS/VSC/TRC > Utility
      Tester Display
      ECB Utility

      • ECB: Electronically Controlled Brake System

      Result
      Proceed to
      NEXT

    NEXT

  3. RECONFIRM DTC


    1. Turn the engine switch off.

    2. Clear the DTCs.

      Click here


      Chassis > ABS/VSC/TRC > Clear DTCs

    3. Turn the engine switch off.

    4. Turn the engine switch on (IG).

    5. Check if the same DTC is output.

      Click here


      Chassis > ABS/VSC/TRC > Trouble Codes
      Result
      Result Proceed to
      DTCs C1345/66 and C1368/67 are not output. A
      DTCs C1345/66 and/or C1368/67 are output. B

    A

    END

    B

    REPLACE BRAKE ACTUATOR ASSEMBLY for RHD: Click here
    REPLACE BRAKE ACTUATOR ASSEMBLY for LHD: Click here