ELECTRONICALLY CONTROLLED BRAKE SYSTEM INITIALIZATION


  1. DESCRIPTION


    1. Perform initialization and calibration of the linear solenoid valve when the skid control ECU assembly, brake actuator assembly, brake pedal stroke sensor assembly or yaw rate sensor is replaced.

      Follow the procedure to perform initialization.

      Tech Tips


      • If there is a problem with the battery (12 V) voltage, initialization and calibration of the linear solenoid valve cannot complete normally. Make sure to check the battery voltage before performing initialization and calibration of the linear solenoid valve.

      • If the actuator temperature is high, initialization and calibration of the linear solenoid valve may not complete normally. If so, wait until the temperature decreases and then perform initialization and calibration of the linear solenoid valve.

      • If the engine switch is turned off, the brake pedal is depressed or the vehicle speed signal is input while linear solenoid valve offset learning is being performed, learning will be canceled.

      Part to be Replaced Necessary Operation

      • Skid control ECU assembly

      • Brake pedal stroke sensor assembly

      • Yaw rate sensor

      • Brake pedal support assembly

      1. Clear stored linear solenoid valve calibration data.

      2. Perform initialization and calibration of the linear solenoid valve.
      Brake actuator assembly

      1. Bleed air.

      2. Clear stored linear solenoid valve calibration data.

      3. Perform initialization and calibration of the linear solenoid valve.

  2. PERFORM INITIALIZATION AND CALIBRATION OF LINEAR SOLENOID VALVE


    1. Clear the stored linear solenoid valve calibration data.


      1. Turn the engine switch on (IG).

      2. Check that the shift position is in P.

      3. Check that the steering wheel is centered.

      4. Turn the engine switch off.

      5. Connect the GTS to the DLC3.

      6. Turn the engine switch on (IG).

      7. Check that the parking brake is applied.

      8. Turn the GTS on.

      9. Select the skid control ECU assembly to clear the linear solenoid valve calibration data using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.


        Chassis > ABS/VSC/TRC > Utility
        Tester Display
        Reset Memory

    2. Perform initialization and calibration of the linear solenoid valve.


      1. Turn the engine switch on (IG).

      2. Check that the shift position is in P.

      3. Check that the steering wheel is centered.

      4. Turn the engine switch off.

      5. Connect the GTS to the DLC3.

      6. Check that the parking brake is released.

      7. Turn the engine switch on (IG) with the brake pedal released.

        Note


        • If linear solenoid valve offset learning is performed without turning the engine switch on (IG), the learning process may not be completed properly because of insufficient battery voltage.

        • When linear solenoid valve offset learning is interrupted, or the learning process is performed with the shift position is not in P, DTC C1345 (Linear Solenoid Valve Offset Learning Undone) will be stored.

      8. Turn the GTS on.

      9. Switch the skid control ECU assembly to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / ECB* Utility / Linear Valve Offset.

        *: Electronically Controlled Brake System


        Chassis > ABS/VSC/TRC > Utility
        Tester Display
        ECB Utility

        • ECB: Electronically Controlled Brake System

      10. Leave the vehicle stationary without depressing the brake pedal for 1 or 2 minutes.

      11. Check that the interval between blinks of the brake warning light / yellow (minor malfunction) changes from 1 second to 0.25 seconds.

        Tech Tips


        • The time needed to complete initialization and calibration of the linear solenoid valve varies depending on battery voltage.

        • The brake warning light / yellow (minor malfunction) blinks at 1 second intervals during initialization and calibration of the linear solenoid valve and then changes to the Test Mode blinking pattern.

        • The brake warning light / yellow (minor malfunction) blinks at 0.25 second intervals if the Test Mode is normal.

        • Do not exit Test Mode within 5 seconds of entering Test Mode. If Test Mode is exited within 5 seconds of entering Test Mode, DTC U1104 may be stored. If DTC U1104 is output after exiting Test Mode, enter Test Mode again, wait at least 5 seconds, then recheck for DTCs.

      12. Check that DTC C1345 (Linear Solenoid Valve Offset Learning Undone) which indicates trouble with stroke sensor zero point learning is not output when the brake warning light / yellow (minor malfunction) changes to the Test Mode blinking pattern upon completion of initialization and calibration of the linear solenoid valve.

      13. Perform zero point calibration of the yaw rate sensor.

        Click here

      14. Return to normal mode from Test Mode following the GTS directions.

        Tech Tips

        Refer to the GTS operator's manual for further details.

      15. Turn the engine switch off and disconnect the GTS.