REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)


    1. B000X7RC01
      B000XM7 Diluted Liquid Soap
      B000TT4 Front of the Vehicle

      Apply diluted liquid soap to the outside of a new rear suspension member rear body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member front body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member rear body mounting cushion while confirming the installation direction.

    3. B000UP2N03

      Using SST, install the rear suspension member rear body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mounting cushion.

      SST
      09316-12010
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60020   ( 09951-00910 )

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  2. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

    Tech Tips

    Perform the same procedure as for the LH side.

  3. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION LH


    1. B000XOIC02
      *A for LH Side
      *B for RH Side
      B000XM7 Diluted Liquid Soap
      B000TT4 Front of the Vehicle

      Apply diluted liquid soap to the outside of a new rear suspension member front body mounting cushion.

      Note

      Do not use grease or undiluted liquid soap. Doing so may cause the rear suspension member front body mounting cushion to slip out.

      Tech Tips

      A 20% liquid soap and water concentration is recommended.

    2. Temporarily install the rear suspension member front body mounting cushion while confirming the installation direction.

    3. B000ZALN05

      Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

      SST
      09316-12010
      09570-24011
      09950-40011   ( 09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04051, 09957-04010, 09958-04011 )
      09950-60020   ( 09951-00910 )

      Note

      Apply grease to the threads and tip of the SST center bolt before use.

  4. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION RH

    Tech Tips

    Perform the same procedure as for the LH side.

  5. INSTALL REAR SUSPENSION MEMBER REAR UPPER STOPPER


    1. Install the 2 rear suspension member rear upper stoppers to the rear suspension member sub-assembly.

  6. INSTALL REAR SUSPENSION MEMBER FRONT UPPER STOPPER


    1. Install the 2 rear suspension member front upper stoppers to the rear suspension member sub-assembly.

  7. TEMPORARILY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)


    1. B000YBM

      Insert the rear suspension toe adjust cam sub-assembly from the front of the vehicle. Then temporarily tighten the rear No. 2 suspension toe adjust plate and toe control link sub-assembly LH with the nut.

    2. B000XP5C01
      *a Matchmark

      Align the matchmarks on the rear No. 2 suspension toe adjust plate and rear suspension member sub-assembly.

  8. TEMPORARILY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  9. TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH


    1. B000VPW

      Insert the bolt from the back of the vehicle. Then temporarily tighten the rear upper control arm assembly LH with the nut and washer.

  10. TEMPORARILY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  11. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. B000VHB

      Insert the bolt from the back of the vehicle. Then temporarily tighten the rear No. 1 suspension arm assembly LH with the nut and washer.

  12. TEMPORARILY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  13. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B000VRA

      Insert the rear suspension arm attachment sub-assembly from the back of the vehicle. Then temporarily tighten the rear No. 2 suspension toe adjust plate and rear No. 2 suspension arm assembly LH with the nut.

  14. TEMPORARILY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH


    1. B000Z54

      Insert the bolt from the back of the vehicle. Then temporarily tighten the lower control arm assembly LH with the nut.

  16. TEMPORARILY TIGHTEN LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  17. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION

    Click here

  18. INSTALL REAR STABILIZER BAR

    Click here

  19. INSTALL PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY

    Click here

  20. TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  21. TEMPORARILY TIGHTEN REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  22. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. B000XB4C03
      *a Attachment
      *b Engine Lifter
      B000WCG Attachment placement location

      Support the rear suspension member sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

      CAUTION:


      • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

      • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

      B000WQP

      Note

      Use attachments to keep the rear suspension member sub-assembly level.

    2. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle body.

      Note

      When raising the rear suspension member sub-assembly, be careful not to damage the vehicle body or other components installed to the vehicle.

    3. Install the rear lower suspension member stopper LH, rear lower suspension member stopper RH, 2 rear lower suspension member stoppers and rear suspension member sub-assembly with the 8 bolts.

      Torque:
      Bolt A
      19 N*m  { 194 kgf*cm, 14 ft.*lbf }
      Bolt B
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }

  23. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  24. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  25. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY

    Click here

  26. STABILIZE SUSPENSION

    Click here

  27. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)

    Click here

  28. FULLY TIGHTEN TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  29. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  30. FULLY TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  31. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  32. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  33. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  34. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  35. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY LH

    Click here

  36. FULLY TIGHTEN LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  37. FULLY TIGHTEN REAR STABILIZER LINK ASSEMBLY LH

    Click here

  38. FULLY TIGHTEN REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  39. INSPECT TOE CONTROL LINK SUB-ASSEMBLY LH (w/o Dynamic Rear Steering)

    Click here

  40. INSPECT TOE CONTROL LINK SUB-ASSEMBLY RH (w/o Dynamic Rear Steering)

    Tech Tips

    Perform the same procedure as for the LH side.

  41. INSPECT REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  42. INSPECT REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  43. INSPECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  44. INSPECT REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  45. INSPECT LOWER CONTROL ARM ASSEMBLY LH

    Click here

  46. INSPECT LOWER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  47. CONNECT PARKING BRAKE WITH BRACKET ACTUATOR ASSEMBLY


    1. B000YA9C01
      *a Grommet
      *b Outside of Vehicle
      *c Inside of Vehicle

      Pass the connector through the hole to the inside of the vehicle and install the grommet of the parking brake actuator harness.

    2. Connect the connector.

    3. B000Z12

      Install the parking brake with bracket actuator assembly with the 2 nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  48. INSTALL INNER LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  49. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER

    Click here

  50. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

    Click here

  51. INSTALL LUGGAGE COMPARTMENT TRIM BOX

    Click here

  52. INSTALL LUGGAGE COMPARTMENT TRIM COVER LH

    Click here

  53. INSTALL REAR FLOOR FINISH PLATE

    Click here

  54. INSTALL NO. 1 DECK BOARD

    Click here

  55. ADJUST PARKING BRAKE

    Click here

  56. INSTALL REAR WHEEL

    Click here

  57. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  58. INSTALL NO. 2 DECK BOARD

    Click here

  59. PARKING LOCK

    Click here

  60. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  61. ADJUST REAR TELEVISION CAMERA ASSEMBLY OPTICAL AXIS

    Click here

  62. PERFORM DYNAMIC REAR STEERING SYSTEM CALIBRATION (w/ Dynamic Rear Steering)

    Click here

  63. CHECK FOR SPEED SENSOR SIGNAL

    Click here

  64. PERFORM INITIALIZATION

    Click here

  65. PERFORM PARKING BRAKE SHOE BEDDING

    Click here