FRONT AXLE HUB INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • The following procedure is for the LH side.

  • Other than areas where instructions are provided, use the same procedure for the LH and RH sides.

PROCEDURE


  1. INSTALL DISC BRAKE AIR GUIDE PLATE


    1. Install disc brake air guide plate to the steering knuckle LH.

  2. INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH


    1. Using a hexagon socket wrench 12 mm, install the front axle hub sub-assembly LH with the 4 bolts.

      Torque:
      80 N*m  { 816 kgf*cm, 59 ft.*lbf }

  3. CONNECT STEERING KNUCKLE LH

    Click here

  4. TEMPORARILY TIGHTEN LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. B000V0N

      Insert the bolt from the back of the vehicle. Then temporarily tighten the lower No. 2 suspension arm assembly LH with the nut.

  5. TEMPORARILY TIGHTEN FRONT SHOCK ABSORBER ASSEMBLY LH

    Click here

  6. CONNECT FRONT STABILIZER LINK ASSEMBLY LH

    Click here

  7. CONNECT FRONT HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH

    Click here

  8. TEMPORARILY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    1. B000TTR

      Temporarily tighten the front lower suspension arm assembly LH to the steering knuckle assembly LH with the nut.

  9. CONNECT TIE ROD ASSEMBLY LH

    Click here

  10. INSTALL FRONT DISC BRAKE DUST COVER LH


    1. Install the front disc brake dust cover LH with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  11. INSPECT FRONT AXLE HUB BEARING LOOSENESS

    Click here

  12. INSPECT FRONT AXLE HUB RUNOUT

    Click here

  13. INSTALL FRONT DISC LH

    Click here

  14. CONNECT DISC BRAKE CYLINDER ASSEMBLY


    1. B000W0VN01

      Temporarily install the 5 hub nuts to the front axle hub LH to secure the front disc LH.

      Note

      Do not apply excessive force to the flexible hose.

    2. Temporarily install the disc brake cylinder assembly LH with the bolt on the lower side of the disc brake cylinder assembly LH.

    3. Remove the SST.

    4. B000UZFN01

      Install the disc brake cylinder assembly LH with the bolt (A) and bolt (B).

      Torque:
      135 N*m  { 1377 kgf*cm, 100 ft.*lbf }
    5. B000XHU

      Install the front flexible hose bracket LH to the steering knuckle with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    6. B000XWH

      Connect the flexible hose to the front flexible hose bracket LH with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    7. for RH side:


      1. B000XR0

        Attach the guide to connect the pad wear indicator wire assembly.

  15. CONNECT FRONT SKID CONTROL SENSOR WIRE


    1. B000YEU

      for LH Side:


      1. Install the sensor clamp with the bolt.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Note

        Do not twist the skid control sensor wire when installing it.

      2. Connect the skid control sensor wire connector.

    2. B000X4F

      for RH Side:


      1. Install the sensor clamp with the bolt.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }

        Note

        Do not twist the skid control sensor wire when installing it.

      2. Connect the skid control sensor wire connector.

      3. Connect the pad wear indicator connector.

    3. B000XXV

      Install the sensor clamp with the nut.

      Torque:
      8.5 N*m  { 87 kgf*cm, 75 in.*lbf }

      Note

      Do not twist the skid control sensor wire when installing it.

  16. STABILIZE SUSPENSION

    Click here

  17. FULLY TIGHTEN LOWER NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. Tighten the installation bolt of the lower No. 2 suspension arm assembly LH.

      Torque:
      130 N*m  { 1326 kgf*cm, 96 ft.*lbf }

  18. FULLY TIGHTEN FRONT LOWER SUSPENSION ARM ASSEMBLY LH


    1. Tighten the installation nut of the steering knuckle assembly LH.

      Torque:
      145 N*m  { 1479 kgf*cm, 107 ft.*lbf }

      Note

      Further tighten the nut up to 60° if the holes for the clip are not aligned.

    2. Install a new clip.

  19. FULLY TIGHTEN FRONT SHOCK ABSORBER ASSEMBLY LH


    1. Fully tighten the front shock absorber assembly bolt.

      Torque:
      110 N*m  { 1122 kgf*cm, 81 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  20. INSTALL REAR LOWER ARM MOUNTING REINFORCEMENT SUB-ASSEMBLY LH

    Click here

  21. INSTALL ENGINE SIDE COVER LH

    Click here

  22. INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY

    Click here

  23. INSTALL FRONT WHEEL

    Click here

  24. CONNECT BRAKE BOOSTER PUMP CONNECTOR

    Click here

  25. CHECK FOR SPEED SENSOR SIGNAL

    Click here

  26. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  27. ADJUST HEADLIGHT AIMING

    Click here

  28. ADJUST REAR TELEVISION CAMERA ASSEMBLY OPTICAL AXIS

    Click here