ELECTRONIC SHIFT LEVER SYSTEM, Diagnostic DTC:P1C8D49

DTC Code DTC Name
P1C8D49 Park Pawl Motor Control System (After Lock/Unlock Position Learning) Internal Electronic Failure

DESCRIPTION

Refer to the description for DTC P1C8949.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Warning Indicate
P1C8D49 Park Pawl Motor Control System (After Lock/Unlock Position Learning) Internal Electronic Failure

When the engine switch is on (IG), the power supply voltage is low, an open or short occurs in the P CON MTR relay, P CON MTR2 relay, shift control actuator assembly (parking lock motor and rotation angle sensor) or wire harness, and an internal malfunction occurs in the shift control actuator assembly (parking lock motor and rotation angle sensor) continuously for 1 second or more

(1 trip detection logic)

  • Shift control ECU

  • Battery

  • Sub-battery module assembly

  • Shift control actuator assembly

  • Automatic transmission assembly

  • P CON MTR relay

  • P CON MTR2 relay

  • Wire harness or connector

 Does not come on

  • Master Warning Light


    • Comes on

  • Multi-information Display Error Message


    • Displayed

CONFIRMATION DRIVING PATTERN

Tech Tips

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the All Readiness check procedure.

Click here


  1. Turn the engine switch on (IG).

  2. Depress the brake pedal and move the shift lever to select neutral (N).

  3. Push the P position switch (shift position indicator) to select park (P).

WIRING DIAGRAM

Refer to the wiring diagram for DTC P1C8949.

Click here

CAUTION / NOTICE / HINT

Note


  • After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • The vehicle is equipped with a sub-battery. Therefore, ensure there is no power being supplied to the vehicle when disconnecting or reconnecting the connector of the shift control ECU and when removing or installing the shift control ECU.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK DTC OUTPUT (TRANSMISSION)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check if DTCs are output.

      Result
      Result Proceed to
      None of the DTCs in the table below are output. A
      Any of the DTCs in the table below are output. B
      Priority Relevant DTC
      1 P085D94 Gear Shift Control Module "A" Unexpected Operation
      P1761A2 Gear Shift Control Module "A" System Voltage Low
      P1765A2 Sub Battery Module System Voltage Low
      P176D12 IG2 Signal (Gear Shift Control Module "A") Circuit Short to Battery
      P176949 Gear Shift Control Module "A" Internal Electronic Failure
      2 P1C8F14 Park Pawl Motor Phase U Circuit Short to Ground or Open
      P1C9414 Park Pawl Motor Phase V Circuit Short to Ground or Open
      P1C9914 Park Pawl Motor Phase W Circuit Short to Ground or Open

      Tech Tips

      The chart above is listed in inspection order of priority.

    5. Turn the engine switch off.


    B

    GO TO DTC CHART Click here

    A

  2. CHECK FREEZE FRAME DATA (BATT VOLTAGE FOR GEAR SHIFT CONTROL MODULE)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      Tech Tips

      It may not be possible to start the engine.

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Read the freeze frame data of DTC P1C8D49.


      Powertrain > Transmission
      Tester Display
      BATT Voltage for Gear Shift Control Module
      Result
      Result Proceed to
      BATT Voltage for Gear Shift Control Module is 9 V or higher. A
      BATT Voltage for Gear Shift Control Module is below 9 V. B

    5. Turn the engine switch off.


    B

    CHARGE BATTERY Click here

    A

  3. CHECK FREEZE FRAME DATA (PROTECTION RELAY STATUS)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

      Tech Tips

      It may not be possible to start the engine.

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Read the freeze frame data of DTC P1C8D49.


      Body Electrical > Sub Battery Module
      Tester Display
      Protection Relay Status

    5. Enter the following menus: Body Electrical / Sub Battery Module / Active Test / Protection Relay


      Body Electrical > Sub Battery Module > Active Test
      Active Test Display
      Protection Relay
      Powertrain > Transmission > Dual Data List
      Data List Display
      Sub Battery Module Voltage

    6. Using the Dual Data List function in the GTS, read the Data List item "Sub Battery Module Voltage" during the Active Test (protection relay ON).

      Result
      Result Proceed to
      The freeze frame data item "Protection Relay Status" is ON and the "Sub Battery Module Voltage" is 9 V or higher while the Active Test is being performed (protection relay ON) A
      The freeze frame data item "Protection Relay Status" is ON and the "Sub Battery Module Voltage" is below 9 V while the Active Test is being performed (protection relay ON) B
      The freeze frame data item "Protection Relay Status" is OFF C

    7. Turn the engine switch off.


    B

    CHECK SUB BATTERY SYSTEM Click here

    C

    GO TO STEP 8 Click here

    A

  4. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check for DTCs and freeze frame data and then write them down.

      Tech Tips

      When DTCs are cleared, the freeze frame data is also cleared. The freeze frame data stored when the DTCs are detected is required for troubleshooting. Therefore, check and record the stored DTC information before clearing them.

    5. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    6. Turn the engine switch off.

    7. Disconnect the GTS from the DLC3.

    8. Leave the vehicle as is for 60 seconds or more.

      Note


      • Do not connect the GTS.

      • Do not depress brake pedal.

      • Do not open/close any of the doors.

      Result
      Proceed to
      NEXT

    NEXT

  5. CHARGE BATTERY


    1. Charge the battery.

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK DTC OUTPUT (SIMULATION TEST)


    1. Start the engine.

    2. Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.

    3. Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

    4. Stop the vehicle and push the P position switch (shift position indicator) to select park (P).

    5. Turn the engine switch off.

    6. Connect the GTS to the DLC3.

    7. Turn the engine switch on (IG) and wait for 10 seconds or more.

      Tech Tips

      It may not be possible to start the engine.

    8. Depress the brake pedal and move the shift lever to select neutral (N).

    9. Push the P position switch (shift position indicator) to select park (P).

    10. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    11. Check if DTCs are output.

      Result
      Result Proceed to
      Only DTC P1C8D49 is output. A
      None of the DTCs are output. B
      DTCs other than P1C8D49 are also output C

    12. Turn the engine switch off.


    B

    END (BATTERY WAS INSUFFICIENTLY CHARGED)

    C

    GO TO DTC CHART Click here

    A

  7. CHECK FREEZE FRAME DATA (PARKING LOCK MOTOR MAIN RELAY STATUS, PARKING LOCK MOTOR BACKUP RELAY STATUS)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Read the freeze frame data of DTC P1C8D49.


      Powertrain > Transmission
      Tester Display
      Parking Lock Motor Backup Relay Status
      Parking Lock Motor Main Relay Status
      Result
      Result Proceed to
      Parking Lock Motor Main Relay Status is ON. A
      Parking Lock Motor Backup Relay Status is ON. B

    5. Turn the engine switch off.


    B

    CHECK FREEZE FRAME DATA (U, V, W VOLTAGE) Click here

    A

  8. CHECK FREEZE FRAME DATA (U, V, W VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Read the freeze frame data of DTC P1C8D49.


      Powertrain > Transmission
      Tester Display
      U Phase Parking Lock Motor Terminal Voltage
      V Phase Parking Lock Motor Terminal Voltage
      W Phase Parking Lock Motor Terminal Voltage
      Result
      Tester Display Specified Condition
      W Phase Parking Lock Motor Terminal Voltage 1 to 2 V
      V Phase Parking Lock Motor Terminal Voltage 1 to 2 V
      U Phase Parking Lock Motor Terminal Voltage 1 to 2 V

    5. Turn the engine switch off.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT) Click here

    OK

  9. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - ROTATION ANGLE SENSOR (SHIFT CONTROL ACTUATOR ASSEMBLY))


    1. Disconnect the A53 shift control ECU connector.

    2. Disconnect the G41 rotation angle sensor (shift control actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A53-22(VC) - G41-10(RVC) Always Below 1 Ω
      A53-23(RA) - G41-5(RA) Always Below 1 Ω
      A53-21(RB) - G41-3(RB) Always Below 1 Ω
      A53-24(E2) - G41-8(RE2) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A53-22(VC) or G41-10(RVC) - Body ground and other terminals Always 10 kΩ or higher
      A53-23(RA) or G41-5(RA) - Body ground and other terminals Always 10 kΩ or higher
      A53-21(RB) or G41-3(RB) - Body ground and other terminals Always 10 kΩ or higher
      A53-24(E2) or G41-8(RE2) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the G41 rotation angle sensor (shift control actuator assembly) connector.

    5. Reconnect the A53 shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - BODY GROUND)


    1. B000Z3NC08
      *a

      Front view of wire harness connector

      (to Shift Control ECU)

      Disconnect the shift control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      P75-6(E01) - Body ground Always Below 1 Ω
      P75-5(E02) - Body ground Always Below 1 Ω
      P75-4(E03) - Body ground Always Below 1 Ω

    3. Reconnect the shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK SHIFT CONTROL ACTUATOR ASSEMBLY


    1. Check that the parking brake is applied.

    2. Pull the shift control actuator assembly from the automatic transmission assembly.

      Click here

    3. Reconnect the G41 shift control actuator assembly connector.

    4. Release the brake pedal and turn the engine switch on (ACC).

      Note

      The shift control actuator assembly may operate if the engine switch is turned on (IG). Do not turn the engine switch on (IG) during this inspection to prevent the shift control actuator assembly from operating while in contact with the splines.

    5. B000Y36

      Using a screwdriver with its tip wrapped with protective tape or a piece of cloth, rotate the shaft.

      Note


      • During this inspection, make sure to use a screwdriver with its tip wrapped with protective tape or a piece of cloth to prevent the splines of the actuator from being damaged.

      • Rotate the shaft with torque of 2 N*m (20.3 kgf*cm, 17.7 in.*lbf) or less. Do not apply load while the contacting the stopper inside the actuator.

      • The shift control actuator assembly cannot be disassembled.


      1. Confirm that the shaft of the shift control actuator assembly rotates smoothly.

        OK
        The shaft of the shift control actuator assembly rotates smoothly.

      2. Measure the voltage according to the value(s) in the table below.

        Note

        When measuring the voltage, turn the shift control actuator assembly slowly.

        B000UQBC03
        *a

        Component with harness connected

        (Shift Control ECU)
        *b Output Waveform while Splines of Shift Control Actuator Assembly being Rotated (Example)
        Standard Voltage
        Tester Connection Condition Specified Condition
        A53-23(RA) - A53-24(E2) Engine switch on (ACC), shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V
        A53-21(RB) - A53-24(E2) Engine switch on (ACC), shaft of shift control actuator assembly being rotated 0 to 1.5 V ←→ 4 to 5.5 V

    6. Turn the engine switch off.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY Click here

    OK

  12. CHECK ROTATION ANGLE SENSOR (SHIFT CONTROL ACTUATOR ASSEMBLY)


    1. B000WYCC05
      *a

      Front view of wire harness connector

      (to Shift Control ECU)

      Disconnect the shift control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      A53-22(VC) - A53-23(RA) Engine switch off 10 kΩ or higher
      A53-22(VC) - A53-21(RB) Engine switch off 10 kΩ or higher
      A53-22(VC) - A53-24(E2) Engine switch off 590 to 670 Ω
      A53-23(RA) - A53-21(RB) Engine switch off 10 kΩ or higher
      A53-23(RA) - A53-24(E2) Engine switch off 10 kΩ or higher
      A53-21(RB) - A53-24(E2) Engine switch off 10 kΩ or higher

    3. Reconnect the shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY Click here

    OK

  13. CHECK AUTOMATIC TRANSMISSION ASSEMBLY


    1. B000VULC01
      *a Lock
      *b Unlock
      *c Rotate approximately 20°

      Wrap the shaft with a piece of cloth and turn it using pliers.

      OK
      The shaft rotates smoothly in the lock and unlock directions.

      Note


      • Rotate the shaft using torque between 4.0 and 7.0 N*m (41 and 71 kgf*cm, 36 and 61 in.*lbf).

      • During this inspection, make sure to use a piece of cloth to prevent the shaft splines from being damaged.

    2. Set the shaft in the lock position after the inspection.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SHIFT CONTROL ECU Click here

    NG

    REPLACE AUTOMATIC TRANSMISSION ASSEMBLY Click here

  14. CHARGE BATTERY


    1. Charge the battery.

      Result
      Proceed to
      NEXT

    NEXT

  15. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check for DTCs and freeze frame data and then write them down.

    5. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    6. Turn the engine switch off.

    7. Disconnect the GTS from the DLC3.

    8. Leave the vehicle as is for 60 seconds or more.

      Note


      • Do not connect the GTS.

      • Do not depress brake pedal.

      • Do not open/close any of the doors.

      Result
      Proceed to
      NEXT

    NEXT

  16. CHECK DTC OUTPUT (SIMULATION TEST)


    1. Start the engine.

    2. Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.

    3. Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

    4. Stop the vehicle and push the P position switch (shift position indicator) to select park (P).

    5. Turn the engine switch off.

    6. Connect the GTS to the DLC3.

    7. Turn the engine switch on (IG) and wait for 10 seconds or more.

      Tech Tips

      It may not be possible to start the engine.

    8. Depress the brake pedal and move the shift lever to select neutral (N).

    9. Push the P position switch (shift position indicator) to select park (P).

    10. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    11. Check if DTCs are output.

      Result
      Result Proceed to
      None of the DTCs are output. A
      Only DTC P1C8D49 is output. B
      DTCs other than P1C8D49 are also output C

    12. Turn the engine switch off.


    A

    END

    B

    REPLACE BATTERY Click here

    C

    GO TO DTC CHART Click here

  17. CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT)


    1. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

      B000UGYC01
      *A for RHD *B for LHD
      *1 No. 1 Engine Room Relay Block and Junction Block Assembly *2 P CON MTR Relay

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P CON MTR relay terminal 3 or 2 - Body ground Engine switch off 8 to 15.4 V

    3. Install the P CON MTR relay.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (BATTERY - P CON MTR RELAY) Click here

    OK

  18. INSPECT P CON MTR RELAY


    1. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

      B000VIHC01
      *A for RHD *B for LHD
      *1 No. 1 Engine Room Relay Block and Junction Block Assembly *2 P CON MTR Relay
    2. B000VATC02
      *1 P CON MTR Relay

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Battery voltage applied between terminals 1 and 2 Below 1 Ω

    3. Install the P CON MTR relay.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE P CON MTR RELAY

    OK

  19. CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY - SHIFT CONTROL ECU)


    1. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    2. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

    3. Disconnect the A53 shift control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      P CON MTR relay terminal 5 - G41-7(BMA) Always Below 1 Ω
      P CON MTR relay terminal 1 - A53-12(BMA1) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      P CON MTR relay terminal 5 or G41-7(BMA) - Body ground and other terminals (except P CON MTR2 relay terminal 5) Always 10 kΩ or higher
      P CON MTR relay terminal 1 or A53-12(BMA1) - Body ground and other terminals Always 10 kΩ or higher

    5. Reconnect the A53 shift control ECU connector.

    6. Install the P CON MTR relay.

    7. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  20. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))


    1. Disconnect the A53 shift control ECU connector.

    2. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A53-5(MUA) - G41-2(MUA) Always Below 1 Ω
      A53-2(MVA) - G41-6(MVA) Always Below 1 Ω
      A53-1(MWA) - G41-1(MWA) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A53-5(MUA) or G41-2(MUA) - Body ground and other terminals Always 10 kΩ or higher
      A53-2(MVA) or G41-6(MVA) - Body ground and other terminals Always 10 kΩ or higher
      A53-1(MWA) or G41-1(MWA) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

    5. Reconnect the A53 shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  21. INSPECT PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY)


    1. B000V5KC03
      *1 Parking Lock Motor (Shift Control Actuator Assembly)

      Disconnect the parking lock motor (shift control actuator assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      2(MUA) - 7(BMA) Always 0.5 to 2 Ω
      6(MVA) - 7(BMA) Always 0.5 to 2 Ω
      1(MWA) - 7(BMA) Always 0.5 to 2 Ω
      2(MUA) - 6(MVA) Always 1 to 4 Ω
      6(MVA) - 1(MWA) Always 1 to 4 Ω
      1(MWA) - 2(MUA) Always 1 to 4 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      2(MUA) - Body ground Always 10 kΩ or higher
      6(MVA) - Body ground Always 10 kΩ or higher
      1(MWA) - Body ground Always 10 kΩ or higher

    3. Reconnect the parking lock motor (shift control actuator assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SHIFT CONTROL ECU Click here

    NG

    REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY Click here

  22. CHECK HARNESS AND CONNECTOR (BATTERY - P CON MTR RELAY)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      Battery positive (+) cable - P CON MTR relay terminal 3 or 2 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      Battery positive (+) cable or P CON MTR relay terminal 3 or 2 - Body ground and other terminals Always 10 kΩ or higher

    5. Install the P CON MTR relay.

    6. Reconnect the cable to the positive (+) battery terminal.

    7. Reconnect the cable to the negative (-) battery terminal.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  23. CHARGE BATTERY


    1. Charge the battery.

      Result
      Proceed to
      NEXT

    NEXT

  24. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check for DTCs and freeze frame data and then write them down.

    5. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    6. Turn the engine switch off.

    7. Disconnect the GTS from the DLC3.

    8. Leave the vehicle as is for 60 seconds or more.

      Note


      • Do not connect the GTS.

      • Do not depress brake pedal.

      • Do not open/close any of the doors.

      Result
      Proceed to
      NEXT

    NEXT

  25. CHECK DTC OUTPUT (SIMULATION TEST)


    1. Start the engine.

    2. Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.

    3. Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

    4. Stop the vehicle and push the P position switch (shift position indicator) to select park (P).

    5. Turn the engine switch off.

    6. Connect the GTS to the DLC3.

    7. Turn the engine switch on (IG) and wait for 10 seconds or more.

      Tech Tips

      It may not be possible to start the engine.

    8. Depress the brake pedal and move the shift lever to select neutral (N).

    9. Push the P position switch (shift position indicator) to select park (P).

    10. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    11. Check if DTCs are output.

      Result
      Result Proceed to
      None of the DTCs are output. A
      Only DTC P1C8D49 is output. B
      DTCs other than P1C8D49 are also output C

    12. Turn the engine switch off.


    A

    END

    B

    REPLACE BATTERY Click here

    C

    GO TO DTC CHART Click here

  26. CHECK FREEZE FRAME DATA (U, V, W VOLTAGE)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Read the freeze frame data of DTC P1C8D49.


      Powertrain > Transmission
      Tester Display
      U Phase Parking Lock Motor Terminal Voltage
      V Phase Parking Lock Motor Terminal Voltage
      W Phase Parking Lock Motor Terminal Voltage
      Result
      Tester Display Specified Condition
      W Phase Parking Lock Motor Terminal Voltage 1 to 2 V
      V Phase Parking Lock Motor Terminal Voltage 1 to 2 V
      U Phase Parking Lock Motor Terminal Voltage 1 to 2 V

    5. Turn the engine switch off.

      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 9 Click here

    NG

  27. CHECK HARNESS AND CONNECTOR (P CON MTR RELAY POWER SOURCE CIRCUIT)


    1. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

      B000UGYC01
      *A for RHD *B for LHD
      *1 No. 1 Engine Room Relay Block and Junction Block Assembly *2 P CON MTR Relay

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      P CON MTR relay terminal 3 or 2 - Body ground Engine switch off 8 to 15.4 V

    3. Install the P CON MTR relay.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (BATTERY - P CON MTR RELAY) Click here

    OK

  28. INSPECT P CON MTR RELAY


    1. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

      B000VIHC01
      *A for RHD *B for LHD
      *1 No. 1 Engine Room Relay Block and Junction Block Assembly *2 P CON MTR Relay
    2. B000VATC02
      *1 P CON MTR Relay

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Battery voltage applied between terminals 1 and 2 Below 1 Ω

    3. Install the P CON MTR relay.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE P CON MTR RELAY Click here

    OK

  29. CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR RELAY - SHIFT CONTROL ECU)


    1. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    2. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

    3. Disconnect the A53 shift control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      P CON MTR relay terminal 5 - G41-7(BMA) Always Below 1 Ω
      P CON MTR relay terminal 1 - A53-12(BMA1) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      P CON MTR relay terminal 5 or G41-7(BMA) - Body ground and other terminals (except P CON MTR2 relay terminal 5) Always 10 kΩ or higher
      P CON MTR relay terminal 1 or A53-12(BMA1) - Body ground and other terminals Always 10 kΩ or higher

    5. Reconnect the A53 shift control ECU connector.

    6. Install the P CON MTR relay.

    7. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  30. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))


    1. Disconnect the A53 shift control ECU connector.

    2. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A53-5(MUA) - G41-2(MUA) Always Below 1 Ω
      A53-2(MVA) - G41-6(MVA) Always Below 1 Ω
      A53-1(MWA) - G41-1(MWA) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A53-5(MUA) or G41-2(MUA) - Body ground and other terminals Always 10 kΩ or higher
      A53-2(MVA) or G41-6(MVA) - Body ground and other terminals Always 10 kΩ or higher
      A53-1(MWA) or G41-1(MWA) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

    5. Reconnect the A53 shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  31. CHECK HARNESS AND CONNECTOR (P CON MTR2 RELAY POWER SOURCE CIRCUIT)


    1. B000TONC02
      *1 No. 2 Luggage Room Relay Block Assembly
      *2 P CON MTR2 Relay

      Remove the P CON MTR2 relay from the No. 2 luggage room relay block assembly.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      P CON MTR2 relay terminal 3 or 2 - Body ground 5 seconds after turning the engine switch on (IG) 8 to 15.4 V

      Note

      Power is supplied from the sub-battery module assembly for only 5 seconds after the engine switch is turned on (IG). Therefore, measure the voltage during that time.

    4. Turn the engine switch off.

    5. Install the P CON MTR2 relay.

      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (SUB-BATTERY MODULE ASSEMBLY - P CON MTR2 RELAY) Click here

    OK

  32. INSPECT P CON MTR2 RELAY


    1. B000Z1NC02
      *1 No. 2 Luggage Room Relay Block Assembly
      *2 P CON MTR2 Relay

      Remove the P CON MTR2 relay from the No. 2 luggage room relay block assembly.

    2. B000VATC02
      *1 P CON MTR2 Relay

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 - 5 Battery voltage not applied between terminals 1 and 2 10 kΩ or higher
      Battery voltage applied between terminals 1 and 2 Below 1 Ω

    3. Install the P CON MTR2 relay.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE P CON MTR2 RELAY

    OK

  33. CHECK HARNESS AND CONNECTOR (PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY) - P CON MTR2 RELAY - SHIFT CONTROL ECU)


    1. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    2. Remove the P CON MTR2 relay from the No. 2 luggage room relay block assembly.

    3. Disconnect the P74 shift control ECU connector.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      P CON MTR2 relay terminal 5 - G41-7(BMA) Always Below 1 Ω
      P CON MTR2 relay terminal 1 - P74-24(BMA2) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      P CON MTR2 relay terminal 5 or G41-7(BMA) - Body ground and other terminals (except P CON MTR relay terminal 5) Always 10 kΩ or higher
      P CON MTR2 relay terminal 1 or P74-24(BMA2) - Body ground and other terminals Always 10 kΩ or higher

    5. Reconnect the P74 shift control ECU connector.

    6. Install the P CON MTR2 relay.

    7. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  34. CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ECU - PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY))


    1. Disconnect the A53 shift control ECU connector.

    2. Disconnect the G41 parking lock motor (shift control actuator assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      A53-5(MUA) - G41-2(MUA) Always Below 1 Ω
      A53-2(MVA) - G41-6(MVA) Always Below 1 Ω
      A53-1(MWA) - G41-1(MWA) Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      A53-5(MUA) or G41-2(MUA) - Body ground and other terminals Always 10 kΩ or higher
      A53-2(MVA) or G41-6(MVA) - Body ground and other terminals Always 10 kΩ or higher
      A53-1(MWA) or G41-1(MWA) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the G41 parking lock motor (shift control actuator assembly) connector.

    5. Reconnect the A53 shift control ECU connector.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  35. INSPECT PARKING LOCK MOTOR (SHIFT CONTROL ACTUATOR ASSEMBLY)


    1. B000V5KC03
      *1 Parking Lock Motor (Shift Control Actuator Assembly)

      Disconnect the parking lock motor (shift control actuator assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      2(MUA) - 7(BMA) Always 0.5 to 2 Ω
      6(MVA) - 7(BMA) Always 0.5 to 2 Ω
      1(MWA) - 7(BMA) Always 0.5 to 2 Ω
      2(MUA) - 6(MVA) Always 1 to 4 Ω
      6(MVA) - 1(MWA) Always 1 to 4 Ω
      1(MWA) - 2(MUA) Always 1 to 4 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      2(MUA) - Body ground Always 10 kΩ or higher
      6(MVA) - Body ground Always 10 kΩ or higher
      1(MWA) - Body ground Always 10 kΩ or higher

    3. Reconnect the parking lock motor (shift control actuator assembly) connector.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE SHIFT CONTROL ECU Click here

    NG

    REPLACE SHIFT CONTROL ACTUATOR ASSEMBLY Click here

  36. REPLACE P CON MTR RELAY

    Result
    Proceed to
    NEXT

    NEXT

    GO TO STEP 42 Click here

  37. CHECK HARNESS AND CONNECTOR (BATTERY - P CON MTR RELAY)


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Remove the P CON MTR relay from the No. 1 engine room relay block and junction block assembly.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      Battery positive (+) cable - P CON MTR relay terminal 3 or 2 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      Battery positive (+) cable or P CON MTR relay terminal 3 or 2 - Body ground and other terminals Always 10 kΩ or higher

    5. Install the P CON MTR relay.

    6. Reconnect the cable to the positive (+) battery terminal.

    7. Reconnect the cable to the negative (-) battery terminal.

      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  38. CHARGE BATTERY


    1. Charge the battery.

      Result
      Proceed to
      NEXT

    NEXT

  39. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check for DTCs and freeze frame data and then write them down.

    5. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    6. Turn the engine switch off.

    7. Disconnect the GTS from the DLC3.

    8. Leave the vehicle as is for 60 seconds or more.

      Note


      • Do not connect the GTS.

      • Do not depress brake pedal.

      • Do not open/close any of the doors.

      Result
      Proceed to
      NEXT

    NEXT

  40. CHECK DTC OUTPUT (SIMULATION TEST)


    1. Start the engine.

    2. Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.

    3. Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

    4. Stop the vehicle and push the P position switch (shift position indicator) to select park (P).

    5. Turn the engine switch off.

    6. Connect the GTS to the DLC3.

    7. Turn the engine switch on (IG) and wait for 10 seconds or more.

      Tech Tips

      It may not be possible to start the engine.

    8. Depress the brake pedal and move the shift lever to select neutral (N).

    9. Push the P position switch (shift position indicator) to select park (P).

    10. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    11. Check if DTCs are output.

      Result
      Result Proceed to
      None of the DTCs are output. A
      Only DTC P1C8D49 is output. B
      DTCs other than P1C8D49 are also output C

    12. Turn the engine switch off.


    A

    END

    B

    REPLACE BATTERY Click here

    C

    GO TO DTC CHART Click here

  41. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

  42. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    4. Check for DTCs and freeze frame data and then write them down.

    5. Clear the DTCs.


      Powertrain > Transmission > Clear DTCs

    6. Turn the engine switch off.

    7. Disconnect the GTS from the DLC3.

    8. Leave the vehicle as is for 60 seconds or more.

      Note


      • Do not connect the GTS.

      • Do not depress brake pedal.

      • Do not open/close any of the doors.

      Result
      Proceed to
      NEXT

    NEXT

  43. CHECK DTC OUTPUT (SIMULATION TEST)


    1. Start the engine.

    2. Depress the brake pedal and move the shift lever as follows to select each shift state: N → D.

    3. Drive the vehicle at 40 km/h (25 mph) or more for 10 seconds or more.

    4. Stop the vehicle and push the P position switch (shift position indicator) to select park (P).

    5. Turn the engine switch off.

    6. Connect the GTS to the DLC3.

    7. Turn the engine switch on (IG) and wait for 10 seconds or more.

      Tech Tips

      It may not be possible to start the engine.

    8. Depress the brake pedal and move the shift lever to select neutral (N).

    9. Push the P position switch (shift position indicator) to select park (P).

    10. Enter the following menus: Powertrain / Transmission / Trouble Codes.


      Powertrain > Transmission > Trouble Codes

    11. Check if DTCs are output.

      Result
      Result Proceed to
      None of the DTCs are output. A
      Only DTC P1C8D49 is output. B
      DTCs other than P1C8D49 are also output C

    12. Turn the engine switch off.


    A

    END

    B

    GO TO STEP 31 Click here

    C

    GO TO DTC CHART Click here

  44. CHECK HARNESS AND CONNECTOR (SUB-BATTERY MODULE ASSEMBLY - P CON MTR2 RELAY)


    1. Disconnect the b7 positive (+) terminal from the sub-battery module assembly.

      Click here

    2. Remove the P CON MTR2 relay from the No. 2 luggage room relay block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      b7-1(+BAT) - P CON MTR2 relay terminal 3 or 2 Always Below 1 Ω
      Standard Resistance (Check for Short)
      Tester Connection Condition Specified Condition
      b7-1(+BAT) or P CON MTR2 relay terminal 3 or 2 - Body ground and other terminals Always 10 kΩ or higher

    4. Install the P CON MTR2 relay.

    5. Reconnect the b7 positive (+) terminal to the sub-battery module assembly.

      Result
      Proceed to
      OK
      NG

    OK

    CHECK SUB BATTERY SYSTEM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  45. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

    GO TO STEP 42 Click here

  46. REPAIR OR REPLACE HARNESS OR CONNECTOR

    Result
    Proceed to
    NEXT

    NEXT

    GO TO STEP 42 Click here