AUTOMATIC TRANSMISSION SYSTEM, Diagnostic DTC:P071015

DTC Code DTC Name
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open

DESCRIPTION

The ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM.

The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature becomes higher, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage goes down as the temperature becomes higher.

The ECM calculates the fluid temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071015 Transmission Fluid Temperature Sensor "A" Circuit Short to Battery or Open

ATF temperature sensor voltage is higher than 4.915 V for 0.5 seconds or more and either condition is met (1-trip detection logic):


  • 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F).

  • 10 minutes or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are -29.375°C (-20.875°F) or less.

  • Open or short in ATF temperature sensor circuit

  • Transmission wire (ATF temperature sensor)

  • ECM

 Comes on DTC stored SAE: P0713
DTC Detection Condition Patterns
Vehicle Condition
Pattern 1 Pattern 2
Diagnostic Condition 10 seconds or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are higher than -29.375°C (-20.875°F). ○ -
10 minutes or more have elapsed after the engine start when the engine coolant temperature and intake air temperature are -29.375°C (-20.875°F) or less. - ○
Malfunction Condition ATF temperature sensor voltage is higher than 4.915 V. ○ ○
Duration 0.5 seconds or more 0.5 seconds or more
Detection Logic 1-trip detection logic 1-trip detection logic

Tech Tips

This DTC is stored when either of the above detection patterns is met.

MONITOR DESCRIPTION

This DTC indicates an open or short in the ATF temperature sensor circuit. The ATF temperature sensor converts the ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect an open or short in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is higher than 156 kΩ*, the ECM interprets this as a malfunction of the ATF temperature sensor or in the wire harness, illuminates the MIL and stores this DTC.

*: -40°C (-40°F) is indicated regardless of the actual ATF temperature.

Tech Tips

The ATF temperature can be checked in the Data List.

CONFIRMATION DRIVING PATTERN

Tech Tips

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Start the engine and wait for 10 minutes or more.

  7. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  8. Input the DTC: P071015.

  9. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P071011.

Click here

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click here


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.

    7. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      A/T Oil Temperature No.1 ATF temperature sensor value

      Min.: -40°C (-40°F)

      Max.: 150°C (302°F)

      • Approximately 80°C (176°F): After stall speed test

      • Equal to ambient temperature: While engine is cold

      		 If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted

      Powertrain > Transmission > Data List
      Tester Display
      A/T Oil Temperature No.1

      Tech Tips


      • When DTC P071011 is output and the GTS shows 150°C (302°F) or higher, there is a short circuit.

      • When DTC P071015 is output and the GTS shows -40°C (-40°F), there is an open circuit.

        Check the temperature displayed on the GTS in order to check if a malfunction exists.

        Temperature Displayed Malfunction
        -40°C (-40°F) Open circuit
        150°C (302°F) or higher Short circuit

      • If a circuit related to the ATF temperature sensor becomes open, P071015 will be stored in approximately 0.5 seconds. It is not necessary to inspect the circuit when P071000 is output.

PROCEDURE


  1. READ VALUE USING GTS (A/T OIL TEMPERATURE NO. 1)


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Data List / A/T Oil Temperature No.1.

    7. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      A/T Oil Temperature No.1 ATF temperature sensor value

      Min.: -40°C (-40°F)

      Max.: 150°C (302°F)

      • Approximately 80°C (176°F): After stall speed test

      • Equal to ambient temperature: While engine is cold

      		 If value is -40°C (-40°F) or 150°C (302°F), ATF temperature sensor circuit is open or shorted

      Powertrain > Transmission > Data List
      Tester Display
      A/T Oil Temperature No.1
      Result
      Result Proceed to
      Data display is within Normal Condition range A
      Data display is not within Normal Condition range B

    A

    GO TO STEP 3 Click here

    B

  2. CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR - ECM)


    1. B000VELC15
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G42-115 (THO1) - G42-88 (E2) Always 79 Ω to 156 kΩ
      G42-115 (THO1) - Other terminals Always 10 kΩ or higher
      G42-88 (E2) - Other terminals Always 10 kΩ or higher

      Tech Tips

      If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the driveability of the vehicle may decrease.

      ATF Temperature Specified Condition
      10°C (50°F) 5 to 8 kΩ
      25°C (77°F) 2.5 to 4.5 kΩ
      110°C (230°F) 0.22 to 0.28 kΩ
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM) Click here

    OK

  3. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM A/T CODE REGISTRATION Click here

  4. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. Disconnect the G2 transmission wire connector.

    2. Disconnect the G42 ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G2-1 (OIL) - G42-115 (THO1) Always Below 1 Ω
      G2-2 (E2) - G42-88 (E2) Always Below 1 Ω
      G2-1 (OIL) or G42-115 (THO1) - Other terminals Always 10 kΩ or higher
      G2-2 (E2) or G42-88 (E2) - Other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR