OIL PUMP COMPONENTS
ILLUSTRATION
| *1 | ENGINE WIRE | *2 | INJECTOR DRIVER |
| *3 | INJECTOR DRIVER BRACKET | *4 | NO. 5 ENGINE WIRE |
| *5 | NO. 3 ENGINE COVER SUB-ASSEMBLY | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL VAPOR FEED HOSE | *2 | NO. 2 PCV HOSE |
| *3 | NO. 3 PCV HOSE | *4 | PURGE VSV |
| *5 | VACUUM HOSE SUB-ASSEMBLY | *6 | WATER BY-PASS PIPE SUB-ASSEMBLY |
| *7 | NO. 3 WATER BY-PASS HOSE | *8 | WATER BY-PASS HOSE |
| *9 | NO. 5 WATER BY-PASS HOSE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FUEL DELIVERY PIPE SUB-ASSEMBLY | *2 | FUEL TUBE SUB-ASSEMBLY |
| *3 | INJECTOR VIBRATION INSULATOR | *4 | INTAKE AIR SURGE TANK ASSEMBLY |
| *5 | NO. 1 DELIVERY PIPE SPACER | *6 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *7 | NO. 2 FUEL DELIVERY PIPE SUB-ASSEMBLY | *8 | PCV HOSE |
| *9 | THROTTLE BODY WITH MOTOR ASSEMBLY | *10 | NO. 6 ENGINE WIRE |
| *11 | NO. 7 ENGINE WIRE | *12 | NO. 1 FUEL PIPE SUB-ASSEMBLY |
| *13 | GASKET | *14 | THROTTLE BODY GASKET |
| *15 | NO. 2 ENGINE COVER SUB-ASSEMBLY LH | *16 | NO. 4 WATER BY-PASS HOSE |
| *17 | NO. 5 WATER BY-PASS HOSE | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *1 | FUEL PUMP WITH SEAL SUB-ASSEMBLY | *2 | NO. 1 FUEL PIPE SUB-ASSEMBLY |
| *3 | NO. 2 FUEL PIPE SUB-ASSEMBLY | *4 | NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY |
| *5 | NO. 3 FUEL PIPE SUB-ASSEMBLY | *6 | FUEL TUBE SUB-ASSEMBLY |
| *7 | GASKET | *8 | WIRE HARNESS BRACKET |
| *9 | ENGINE WIRE | *10 | NO. 2 ENGINE WIRE |
| *11 | NO. 3 ENGINE COVER SUB-ASSEMBLY | *12 | O-RING |
| *13 | FUEL PUMP INSULATOR | *14 | FUEL PUMP LIFTER ASSEMBLY |
| *15 | FUEL PUMP LIFTER GUIDE | *16 | FUEL PUMP SPACER GASKET |
| *17 | UNION BOLT | - | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| * | For use with a union nut wrench | ● | Non-reusable part |
ILLUSTRATION
| *1 | IGNITION COIL ASSEMBLY | *2 | NO. 2 IDLER PULLEY SUB-ASSEMBLY |
| *3 | OIL PUMP DRIVE SHAFT PULLEY | *4 | WATER INLET HOUSING |
| *5 | WATER PUMP PULLEY | *6 | NO. 5 WATER BY-PASS HOSE |
| *7 | WATER INLET HOSE | *8 | NO. 3 WATER BY-PASS HOSE |
| *9 | NO. 1 WATER INLET HOUSING GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY LH | *2 | SPARK PLUG TUBE GASKET |
| *3 | CYLINDER HEAD COVER GASKET LH | *4 | SPARK PLUG |
| *5 | O-RING | *6 | OIL HOLE GASKET |
| *7 | FUEL PUMP SPACER GASKET | *8 | SEAL WASHER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CYLINDER HEAD COVER SUB-ASSEMBLY | *2 | SPARK PLUG TUBE GASKET |
| *3 | CYLINDER HEAD COVER GASKET | *4 | SPARK PLUG |
| *5 | O-RING | *6 | OIL HOLE GASKET |
| *7 | FUEL PUMP SPACER GASKET | *8 | SEAL WASHER |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY LH | *2 | CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY RH |
| *3 | FRONT WATER BY-PASS JOINT | *4 | V-RIBBED BELT TENSIONER ASSEMBLY |
| *5 | GASKET | *6 | O-RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | CRANKSHAFT PULLEY ASSEMBLY | *2 | OIL FILTER BRACKET SUB-ASSEMBLY |
| *3 | TIMING CHAIN COVER ASSEMBLY | *4 | TIMING GEAR CASE OR TIMING CHAIN CASE OIL SEAL |
| *5 | WATER INLET PIPE | *6 | OIL PUMP GASKET |
| *7 | CRANKSHAFT PULLEY SET BOLT | *8 | OIL FILTER BRACKET STAY |
| *9 | O-RING | *10 | GASKET |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
MP Grease |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | NO. 1 OIL PIPE | *2 | NO. 2 OIL PIPE |
| *3 | NO. 3 OIL PIPE | *4 | SCAVENGING PUMP ASSEMBLY |
| *5 | OIL PIPE SEAL | *6 | O-RING |
| *7 | GASKET | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
ILLUSTRATION
| *1 | OIL PUMP COVER | *2 | OIL PUMP RELIEF VALVE |
| *3 | OIL PUMP ROTOR SET | *4 | OIL PUMP RELIEF VALVE SPRING |
| *5 | OIL PUMP RELIEF VALVE PLUG | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |