CAMSHAFT POSITION SENSOR INSTALLATION

PROCEDURE

1. INSTALL VVT SENSOR (for Intake Side of Bank 1)

   
   

   1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

      Note

      If reusing the VVT sensor, be sure to inspect the O-ring.

   2. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque:

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      
      

      • If the VVT sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or does not move out of place during installation.

   3. Connect the VVT sensor connector.

2. INSTALL NO. 3 FUEL PIPE SUB-ASSEMBLY

   Click here

3. INSTALL VVT SENSOR (for Intake Side of Bank 2)

   
   

   1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

      Note

      If reusing the VVT sensor, be sure to inspect the O-ring.

   2. 

      *a	10 mm Union Nut Wrench
      *b	Torque Wrench Fulcrum Length

      Using a 10 mm union nut wrench, install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque:

      Specified tightening torque

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      
      

      • If the VVT sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or does not move out of place during installation.

      Tech Tips

      
      

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.378 in.)):8.8 N*m (90 kgf*cm, 78 in.*lbf)

   3. Connect the VVT sensor connector.

4. INSTALL VVT SENSOR (for Exhaust Side of Bank 2)

   
   

   1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

      Note

      If reusing the VVT sensor, be sure to inspect the O-ring.

   2. Install the VVT sensor to the cylinder head cover sub-assembly with the bolt.

      Torque:

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      
      

      • If the VVT sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or does not move out of place during installation.

   3. Connect the VVT sensor connector.

5. INSTALL VVT SENSOR (for Exhaust Side of Bank 1)

   
   

   1. Apply a light coat of engine oil to the O-ring of the VVT sensor.

      Note

      If reusing the VVT sensor, be sure to inspect the O-ring.

   2. Install the VVT sensor to the cylinder head cover sub-assembly LH with the bolt.

      Torque:

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      
      

      • If the VVT sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or does not move out of place during installation.

   3. Connect the VVT sensor connector.

6. INSTALL CAMSHAFT POSITION SENSOR

   
   

   1. Apply a light coat of engine oil to the O-ring of the camshaft position sensor.

      Note

      If reusing the camshaft position sensor, be sure to inspect the O-ring.

   2. Install the camshaft position sensor to the cylinder head cover sub-assembly with the bolt.

      Torque:

      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      
      

      • If the camshaft position sensor has been struck or dropped, replace it.

      • Make sure that the O-ring is not cracked or does not move out of place during installation.

   3. Connect the camshaft position sensor connector.

7. INSPECT FOR ENGINE OIL LEAK

   Click here

8. INSTALL V-BANK COVER SUB-ASSEMBLY

   Click here