THEFT DETERRENT SYSTEM TERMINALS OF ECU


  1. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND DRIVER SIDE JUNCTION BLOCK ASSEMBLY

    B000YCPC11
    *1 Main body ECU (multiplex network body ECU) - -

    1. Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly.

      Click here

    2. Connect the driver side junction block assembly connectors.

    3. Measure the voltage and resistance according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition
      A-11 (GND1) - Body ground None - Body ground Ground Always Below 1 Ω
      A-30 (ACC) - Body ground None - Body ground ACC power supply Engine switch on (ACC) 11 to 14 V
      Engine switch off Below 1 V
      A-31 (BECU) - Body ground None - Body ground Battery power supply Always 11 to 14 V
      A-32 (IG) - Body ground None - Body ground IG power supply Engine switch on (IG) 11 to 14 V
      Engine switch off Below 1 V
      P7-1 (FLCY) - Body ground R - Body ground Courtesy light switch LH input signal Front door LH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
      P7-6 (FRCY) - Body ground SB - Body ground Courtesy light switch RH input signal Front door RH closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
      A-4 (LGCY) - Body ground None - Body ground Luggage compartment door courtesy light switch signal Luggage compartment door closed (OFF) → open (ON) 10 kΩ or higher → Below 1 Ω
      P7-30 (HCTY) - Body ground P - Body ground Engine hood courtesy switch input signal Engine hood open (OFF) → closed (ON) 10 kΩ or higher → Below 1 Ω

    4. Install the main body ECU (multiplex network body ECU) to the driver side junction block assembly.

      Click here

    5. Measure the voltage and check for pulses according to the value(s) in the table below.

      Tester Connection Wiring Color Terminal Description Condition Specified Condition

      3D-31 (LSFL) - Body ground*1

      3A-15 (LSFL) - Body ground*2

      P - Body ground*1

      Y - Body ground*2

      		 Front door LH unlock detection switch input signal Front door LH unlocked Below 1 V
      Engine switch off, all doors closed and front door LH locked Pulse generation

      3B-14 (LSFR) - Body ground*1

      3D-31 (LSFR) - Body ground*2

      GR - Body ground*1

      P - Body ground*2

      		 Front door RH unlock detection switch input signal Front door RH unlocked Below 1 V
      Engine switch off, all doors closed and front door RH locked Pulse generation
      P9-12 (SSCL) - Body ground R - Body ground Theft warning siren assembly drive Theft warning siren assembly sounding (Theft deterrent system is in alarm sounding state) Pulse generation (Below 1 V ←→ 11 to 14 V)
      P9-3 (SSW1) - Body ground V - Body ground Intrusion sensor cancel switch signal Intrusion sensor cancel switch on Below 1 V
      Intrusion sensor cancel switch off Pulse generation
      P9-14 (ISIF) - Body ground B - Body ground Intrusion sensor (theft warning ultrasonic sensor) signal No moving object detected by sensor 11 to 14 V
      Theft deterrent system changes from disarmed state to armed preparation state

      Pulse generation

      (See Waveform 1)
      P9-15 (GCS) - Body ground BE - Body ground Yawrate sensor (theft warning tile sensor) signal Theft deterrent system changes from armed preparation state to armed state

      Pulse generation

      (See Waveform 2)
      P9-1 (GPBS) - Body ground LG - Body ground Glass breakage sensor signal Glass breakage sensor normal Below 2 V
      Glass breakage sensor malfunctioning 4.5 to 14 V

      3C-16 (HORN) - Body ground*1

      3C-28 (HORN) - Body ground*2

      		 P - Body ground Vehicle horn drive Vehicle horns sounding (Theft deterrent system is in alarm sounding state) Pulse generation (Below 1 V ←→ 11 to 14 V)

      • *1: for LHD

      • *2: for RHD

    6. Using an oscilloscope, check the waveform.

      Tech Tips

      The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


      1. Waveform 1 (Reference)

        B000WRXC03
        *a IOUT Initial Signal *b IOUT Initial Response
        *c Approximately 1.0 Second *d Initial Diagnosis
        *e Approximately 1.0 to 1.6 Seconds *f Approximately 0.05 Seconds
        *g Approximately 5.5 Seconds *h Disarmed State
        *i Arming Preparation State - -

      2. Waveform 2 (Reference)

        B000WRXC03
        3. *a CSIF Initial Signal *b CSIF Initial Response
        *c Approximately 1.0 Second *d Initial Diagnosis
        *e Approximately 1.0 to 1.6 Seconds *f Approximately 0.05 Seconds
        *g Approximately 5.5 Seconds *h Disarmed State
        *i Arming Preparation State - -