SFI SYSTEM(w/o Canister Pump Module), Diagnostic DTC:P0017, P0019

DTC Code DTC Name
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)
P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate exhaust valve open and close timing is controlled by the ECM. The ECM performs exhaust valve control by performing the following: 1) controlling the exhaust camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing exhaust gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0017 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B) Deviation in the crankshaft position sensor signal and VVT sensor (bank 1) signal (2 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly LH (bank 1)

  • Oil control valve filter

  • Camshaft timing exhaust gear assembly LH (bank 1)

  • ECM

 Comes on (Euro-OBD) / Does not come on (Except Euro-OBD) DTC stored
P0019 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B) Deviation in the crankshaft position sensor signal and VVT sensor (bank 2) signal (2 trip detection logic).

  • Valve timing

  • Camshaft timing oil control valve assembly RH (bank 2)

  • Oil control valve filter

  • Camshaft timing exhaust gear assembly RH (bank 2)

  • ECM

 Comes on (Euro-OBD) / Does not come on (Except Euro-OBD) DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The exhaust valve timing is set to the most advanced angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores DTC P0017 (bank 1) or P0019 (bank 2).

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing exhaust gear assembly
Required Sensors/Components (Related)

VVT sensor

Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

B000X4IE01

  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG).

  7. Turn the GTS on [A].

  8. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

  9. Idle the engine for 5 minutes or more [C].

  10. Enter the following menus: Powertrain / Engine / Trouble Codes [D].

  11. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  13. Input the DTC: P0017 or P0019.

  14. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  15. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  16. Idle the engine for 5 minutes or more [F].

  17. Enter the following menus: Powertrain / Engine / Trouble Codes [G].

  18. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  19. Check the DTC judgment result.

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

CAUTION / NOTICE / HINT

Tech Tips


  • Bank 1 refers to the bank that includes the No. 1 cylinder*.

    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.

  • Bank 2 refers to the bank that does not include the No. 1 cylinder.

  • The monitor for this DTC detects when the timing chain is shifted by one tooth or more.

  • Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 OR P0019)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.


      Powertrain > Engine > Trouble Codes

    5. Read the DTCs.

      Result
      Result Proceed to
      DTC P0017 and/or P0019 is output A
      DTC P0017 and/or P0019 and other DTCs are output B

      Tech Tips

      If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.


    B

    GO TO DTC CHART Click here

    A

  2. PERFORM ACTIVE TEST USING GTS (CONTROL THE VVT EXHAUST LINEAR BANK 1 OR BANK 2)

    Tech Tips

    If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the A/C switch on.

    4. Turn the GTS on.

    5. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2) / Ptrl Valve Control / VVT Ex Chg Angle #1 or VVT Ex Chg Angle #2.


      Powertrain > Engine > Active Test
      Active Test Display
      Control the VVT Exhaust Linear (Bank1)
      Data List Display
      VVT Ex Chg Angle #1

      Powertrain > Engine > Active Test
      Active Test Display
      Control the VVT Exhaust Linear (Bank2)
      Data List Display
      VVT Ex Chg Angle #2

    6. Perform the Active Test. Check that the displacement angle varies.

      OK
      Displacement angle varies.
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (BANK 1 OR BANK 2) Click here

    OK

  3. CHECK ENGINE MECHANICAL SYSTEM


    1. Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    GO TO STEP 7 Click here

    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

  4. INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (BANK 1 OR BANK 2)


    1. Inspect the camshaft timing oil control valve assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY Click here

    OK

  5. INSPECT OIL CONTROL VALVE FILTER (RH OR LH)

    Result
    Proceed to
    OK
    NG
    B000W5EC03
    *A Bank 1 *B Bank 2
    *1 Oil Control Valve Filter LH *2 Oil Control Valve Filter RH
    *3 Cylinder Head Cover Spacer LH *4 Cylinder Head Cover Spacer RH
    *a Gasket - -

    1. Remove the cylinder head cover sub-assembly.

      Click here

    2. Remove the oil control valve filter RH or LH.

      Click here

    3. Inspect the oil control valve filter RH or LH.

      OK
      Filter is not clogged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE OIL CONTROL VALVE FILTER Click here

    OK

  6. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY (BANK 1 OR BANK 2)


    1. Inspect the camshaft timing exhaust gear assembly.

      Click here

      Tech Tips

      Perform "Inspection After Repair" after replacing the camshaft timing exhaust gear assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY Click here

    OK

  7. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the power switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

    NEXT

  8. CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 AND P0019)


    1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

    3. Read the pending DTCs.


      Powertrain > Engine > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P0017 and/or P0019 is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here