SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P062F

DTC Code DTC Name
P062F Internal Control Module EEPROM Error

DESCRIPTION

The ECM monitors its internal operation and stores this DTC when it detects an internal malfunction.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P062F Internal Control Module EEPROM Error An ECM internal error (EEPROM) (1 trip detection logic). ECM Comes on DTC stored

MONITOR DESCRIPTION

The ECM monitors its internal operation. If the internal operation is malfunctioning, the ECM illuminates the MIL and stores this DTC.

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the GTS off.

  6. Turn the engine switch off.

  7. Disconnect the GTS.

  8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

  9. Connect the cable to the negative (-) battery terminal.

  10. Connect the GTS to the DLC3.

  11. Turn the engine switch on (IG).

  12. Turn the GTS on.

  13. Start the engine and wait 30 seconds or more.

  14. Enter the following menus: Powertrain / Engine / Trouble Codes.

  15. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  17. Input the DTC: P062F.

  18. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

CAUTION / NOTICE / HINT

Note


  • There is a possibility that the DTC P062F is issued from the ECUs of the ECM and TCM.

    Use GTS to conduct a health check to confirm which ECU the DTC is issued from and then inspect the related system.

  • After turning engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine > Clear DTCs

    5. Turn the GTS off.

    6. Turn the engine switch off.

    7. Disconnect the GTS.

    8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

      Result
      Proceed to
      NEXT

    NEXT

  2. READ OUTPUT DTC (DTC P062F)


    1. Connect the cable to the negative (-) battery terminal.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG).

    4. Turn the GTS on.

    5. Start the engine and wait 30 seconds or more.

    6. Enter the following menus: Powertrain / Engine / Trouble Codes.


      Powertrain > Engine > Trouble Codes

    7. Read the DTCs.

      Result
      Result Proceed to
      DTCs are not output A
      DTC P062F is output B

    A

    CHECK FOR INTERMITTENT PROBLEMS Click here

    B

    REPLACE ECM Click here