SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P0192, P0193

DTC Code DTC Name
P0192 Fuel Rail Pressure Sensor Circuit Low Input
P0193 Fuel Rail Pressure Sensor Circuit High Input

DESCRIPTION

B000UU1E28

The fuel pressure sensor is installed on the delivery pipe. The fuel pressure sensor changes the fuel pressure into an electrical signal and sends the signal to the ECM. Then the ECM controls the pump discharge using this feedback to maintain the fuel's target pressure between 2.0 and 18 MPa (20.4 and 183.5 kgf/cm2, 290 and 2611 psi). If the sensor output stops, the ECM will stop the fuel pump with seal sub-assembly (for high pressure side) and supply fuel using the fuel pump with filter assembly (for low pressure side).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0192 Fuel Rail Pressure Sensor Circuit Low Input Open or short in fuel pressure sensor circuit for 3 seconds or more (1 trip detection logic).

  • Open or short in fuel pressure sensor circuit

  • Fuel delivery pipe LH (fuel pressure sensor)

  • ECM

 Comes on DTC stored
P0193 Fuel Rail Pressure Sensor Circuit High Input Open or short in fuel pressure sensor circuit for 3 seconds or more (1 trip detection logic).

  • Open or short in fuel pressure sensor circuit

  • Fuel delivery pipe LH (fuel pressure sensor)

  • ECM

 Comes on DTC stored

Tech Tips

After confirming DTC P0192 and/or P0193 use the GTS to confirm the fuel pressure in the delivery pipe by entering the following menus: Powertrain / Engine / Data List / Ptrl General / Fuel Press.

Fuel Pressure (kPag) Malfunction
Approximately 0

  • PR, E2 circuit short

  • VC circuit open
Approximately 33000 or higher

  • PR, VC circuit short

  • PR circuit open

  • E2 circuit open

MONITOR DESCRIPTION

These DTCs are stored if the fuel pressure sensor output voltage is out of the standard range due to an open or short in the sensor circuit.

MONITOR STRATEGY

Required Sensors/Components Fuel delivery pipe LH (fuel pressure sensor)
Frequency of Operation Continuous

TYPICAL MALFUNCTION THRESHOLDS

P0192
Fuel pressure sensor voltage Less than 0.2933 V
P0193
Fuel pressure sensor voltage Higher than 4.9 V

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Turn the engine switch on (IG).

  7. Turn the GTS on.

  8. Wait 3 seconds or more.

  9. Start the engine.

  10. Idle the engine for 10 seconds [A].

  11. Enter the following menus: Powertrain / Engine / Trouble Codes.

  12. Read the pending DTCs [B].

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  14. Input the DTC: P0192 or P0193.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [A] and [B] again.

WIRING DIAGRAM

B000WBGE05
*a Fuel Delivery Pipe LH (Fuel Pressure Sensor)

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (FUEL PRESS)


    1. Connect the GTS to the DLC3.

    2. Start the engine.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Ptrl General / Fuel Press.


      Powertrain > Engine > Data List
      Tester Display
      Fuel Press

    5. Read the values.

      OK
      3500 to 4500 kPag (idling, warmed up engine).
      Result
      Fuel Pressure (kPag) Proceed to
      Approximately 33000 or higher A
      Approximately 0
      (3500 to 4500)* B

      Tech Tips

      *: The value must change when the engine is moving or stationary.


    B

    CHECK FOR INTERMITTENT PROBLEMS Click here

    A

  2. CHECK HARNESS AND CONNECTOR

    B000WPHC45
    *a

    Front view of wire harness connector

    (to Fuel Delivery Pipe LH (Fuel Pressure Sensor))

    1. Disconnect the fuel delivery pipe LH (fuel pressure sensor) connector.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      J5-1(VC) - J5-2(E2) Engine switch on (IG) 4.75 to 5.25 V
      J5-3(PR) - J5-2(E2) Engine switch on (IG) 3.0 to 5.0 V

    4. Turn the engine switch off and wait for at least 30 seconds.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      J5-1(VC) - J5-3(PR) Engine switch off 171 to 189 kΩ
      J5-2(E2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FUEL DELIVERY PIPE LH (FUEL PRESSURE SENSOR) Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (ECM - FUEL DELIVERY PIPE LH (FUEL PRESSURE SENSOR))


    1. Disconnect the ECM connector.

    2. Disconnect the fuel delivery pipe LH (fuel pressure sensor).

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G42-128 (VCPR) - J5-1 (VC) Always Below 1 Ω
      G42-96 (PR) - J5-3 (PR) Always Below 1 Ω
      G42-127 (EPR) - J5-2 (E2) Always Below 1 Ω
      G42-128 (VCPR) or J5-1 (VC) - Body ground and other terminals Always 10 kΩ or higher
      G42-96 (PR) or J5-3 (PR) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR