REAR COMBINATION LIGHT ASSEMBLY INSPECTION

PROCEDURE

1. INSPECT REAR COMBINATION LIGHT ASSEMBLY LH (for Bulb Type Back-up Light)

   

   *a	Component without harness connected (Rear Combination Light Assembly LH)

   
   

   1. Apply battery voltage to the rear combination light assembly LH and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 1 (TL) Battery negative (-) → Terminal 4 (E) Taillight and side marker light* illuminate Battery positive (+) → Terminal 2 (STP) Battery negative (-) → Terminal 4 (E) Stop light illuminates

      
      

      • *: w/ Rear Side Marker Light

      If the result is not as specified, replace the rear combination light assembly LH.

2. INSPECT REAR COMBINATION LIGHT ASSEMBLY LH (for LED Type Back-up Light)

   

   *a	Component without harness connected (Rear Combination Light Assembly LH)

   
   

   1. Apply battery voltage to the rear combination light assembly LH and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 1 (TL) Battery negative (-) → Terminal 4 (E) Taillight and side marker light illuminate Battery positive (+) → Terminal 2 (STP) Battery negative (-) → Terminal 4 (E) Stop light illuminates Battery positive (+) → Terminal 3 (B) Battery negative (-) → Terminal 4 (E) Turn signal light illuminates

      If the result is not as specified, replace the rear combination light assembly LH.

3. INSPECT REAR COMBINATION LIGHT ASSEMBLY RH (for Bulb Type Back-up Light)

   

   *a	Component without harness connected (Rear Combination Light Assembly RH)

   
   

   1. Apply battery voltage to the rear combination light assembly RH and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 1 (TL) Battery negative (-) → Terminal 4 (E) Taillight and side marker light* illuminate Battery positive (+) → Terminal 2 (STP) Battery negative (-) → Terminal 4 (E) Stop light illuminates

      
      

      • *: w/ Rear Side Marker Light

      If the result is not as specified, replace the rear combination light assembly RH.

4. INSPECT REAR COMBINATION LIGHT ASSEMBLY RH (for LED Type Back-up Light)

   

   *a	Component without harness connected (Rear Combination Light Assembly RH)

   
   

   1. Apply battery voltage to the rear combination light assembly RH and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 1 (TL) Battery negative (-) → Terminal 4 (E) Taillight and side marker light illuminate Battery positive (+) → Terminal 2 (STP) Battery negative (-) → Terminal 4 (E) Stop light illuminates Battery positive (+) → Terminal 3 (B) Battery negative (-) → Terminal 4 (E) Turn signal light illuminates

      If the result is not as specified, replace the rear combination light assembly RH.

5. INSPECT REAR COMBINATION LIGHT LED (for Bulb Type Back-up Light with Rear Side Marker Light)

   

   *a	Component without harness connected (Rear Combination Light LED)

   
   

   1. Apply battery voltage to the rear combination light LED and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 3 (STP) Battery negative (-) → Terminal 2 (E) Stop light illuminates

      If the result is not as specified, replace the rear combination light LED.

6. INSPECT REAR COMBINATION LIGHT LED (for Bulb Type Back-up Light without Rear Side Marker Light)

   

   *a	Component without harness connected (Rear Combination Light LED)

   
   

   1. Apply battery voltage to the rear combination light LED and check that the lights illuminate.

      OK
      Condition Specified Condition Battery positive (+) → Terminal 1 (TL) Battery negative (-) → Terminal 2 (E) Taillight illuminates Battery positive (+) → Terminal 3 (STP) Battery negative (-) → Terminal 2 (E) Stop light illuminates

      If the result is not as specified, replace the rear combination light LED.