OUTER MIRROR SWITCH INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Memory)


    1. Check the mirror select switch and mirror surface adjust switch.


      1. B006XT7C06
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        15 (M+) - 12 (E) Mirror surface adjust switch pushed up 90 to 110 Ω
        Mirror surface adjust switch pushed down 437 to 503 Ω
        Mirror surface adjust switch pushed left 744 to 856 Ω
        Mirror surface adjust switch pushed right 225 to 275 Ω
        Mirror surface adjust switch not pushed 10 kΩ or higher
        13 (MSW) - 12 (E) Mirror select switch turned to R position Below 1 Ω
        Mirror select switch turned to L position 90 to 110 Ω
        Mirror select switch off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check that the LED illuminates.


      1. B006XT7C05
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 14 (ILL+)

        Battery negative (-) - 16 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Memory)


    1. Check the mirror select switch and mirror surface adjust switch. (for LHD, w/ Power Retract Mirror)


      1. B0070C9C01
        *a Mirror Select and Surface Adjust Switch
        *b Mirror Retract Switch
        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        10 (VL) - 7 (B)

        13 (M+) - 5 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VL) - 5 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 7 (B)

        13 (M+) - 5 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 5 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        12 (VR) - 7 (B)

        13 (M+) - 5 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VR) - 5 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (B)

        13 (M+) - 5 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 5 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the mirror retract switch. (for LHD)


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        4 (MF) - 5 (E) Extend position 10 kΩ or higher
        Except extend position Below 1 Ω
        6 (MR) - 5 (E) Retract position 10 kΩ or higher
        Except retract position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    3. Check the mirror select switch and mirror surface adjust switch. (for LHD, w/o Power Retract Mirror)


      1. B006XF4C23
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        10 (VL) - 7 (B)

        13 (M+) - 15 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VL) - 15 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 7 (B)

        13 (M+) - 15 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        9 (HL) - 15 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        12 (VR) - 7 (B)

        13 (M+) - 15 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VR) - 15 (E)

        13 (M+) - 7 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (B)

        13 (M+) - 15 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (E)

        13 (M+) - 7 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check that the LED illuminates. (for LHD)


      1. B006YW9C01
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 8 (ILL+)

        Battery negative (-) - 14 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

    5. Check the mirror select switch and mirror surface adjust switch. (for RHD, w/ Power Retract Mirror)


      1. B0070NCC01
        *a Mirror Select and Surface Adjust Switch
        *b Mirror Retract Switch
        *c

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        12 (VL) - 15 (B)

        9 (M+) - 1 (E)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        12 (VL) - 1 (E)

        9 (M+) - 15 (B)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        13 (HL) - 15 (B)

        9 (M+) - 1 (E)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        13 (HL) - 1 (E)

        9 (M+) - 15 (B)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        10 (VR) - 15 (B)

        9 (M+) - 1 (E)

        		 Up Below 1 Ω
        Off 10 kΩ or higher

        10 (VR) - 1 (E)

        9 (M+) - 15 (B)

        		 Down Below 1 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (B)

        9 (M+) - 1 (E)

        		 Left Below 1 Ω
        Off 10 kΩ or higher

        11 (HR) - 1 (E)

        9 (M+) - 15 (B)

        		 Right Below 1 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    6. Check the mirror retract switch. (for RHD)


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        2 (MF) - 1 (E) Extend position 10 kΩ or higher
        Except extend position Below 1 Ω
        16 (MR) - 1 (E) Retract position 10 kΩ or higher
        Except retract position Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    7. Check the mirror select switch and mirror surface adjust switch. (for RHD, w/o Power Retract Mirror)


      1. B006XF4C24
        *a Mirror Select and Surface Adjust Switch
        *b

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Condition Specified Condition

        12 (VL) - 15 (B)

        9 (M+) - 7 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        12 (VL) - 7 (E)

        9 (M+) - 15 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        13 (HL) - 15 (B)

        9 (M+) - 7 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        13 (HL) - 7 (E)

        9 (M+) - 15 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Condition Specified Condition

        10 (VR) - 15 (B)

        9 (M+) - 7 (E)

        		 Up Below 2 Ω
        Off 10 kΩ or higher

        10 (VR) - 7 (E)

        9 (M+) - 15 (B)

        		 Down Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 15 (B)

        9 (M+) - 7 (E)

        		 Left Below 2 Ω
        Off 10 kΩ or higher

        11 (HR) - 7 (E)

        9 (M+) - 15 (B)

        		 Right Below 2 Ω
        Off 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    8. Check that the LED illuminates. (for RHD)


      1. B006YW9C03
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        OK
        Battery Connection Specified Condition

        Battery positive (+) - 14 (ILL+)

        Battery negative (-) - 8 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.