REAR DOOR DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here


  • Door window regulator sub-assembly

  • Door glass

  • Door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

  3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY


    1. B0070EI

      Using a moulding remover, disengage the 3 claws to remove the rear door armrest cover sub-assembly.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL


    1. B0070Q4C01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the 2 clips, 5 claws and 6 guides as shown in the illustration.

    2. Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.

  5. REMOVE REAR ARMREST ASSEMBLY


    1. B0071I5C01
      B006ZFL Remove in this Direction

      Disengage the 3 clips, 8 claws and 2 guides as shown in the illustration.

    2. B006XY4C01
      B006ZFL Remove in this Direction

      Disengage the guide to remove the rear armrest assembly as shown in the illustration.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. B006YXRC01
      B006Y8C Protective Tape

      Apply protective tape to the rear door panel as shown in the illustration.

    2. B006ZRI

      Remove the 3 screws.

    3. B006YGVC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the 8 clips as shown in the illustration.

    4. B0070B3C01
      B006ZFL Remove in this Direction

      Pull out the rear door trim board sub-assembly as shown in the illustration to disengage the guide.

    5. Raise the rear door trim board sub-assembly to separate the rear door trim board sub-assembly with the rear door inner glass weatherstrip and No. 1 door scuff plate clamp.

    6. B0070FRC01
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly
      B006ZFL Remove in this Direction

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.

    7. B006Y7O

      Using a screwdriver, disengage the claw to remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly.

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. B0071BJC01
      B006ZFL Remove in this Direction

      Slide the rear door inner glass weatherstrip to remove it from the rear door trim board sub-assembly as shown in the illustration.

  8. REMOVE REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)


    1. B006Y5D

      Remove the 9 screws.

    2. Disengage the 3 guides to remove the rear curtain sub-assembly.

  9. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER


    1. B006WZN

      Disengage the clip.

    2. B006YYZ

      Remove the rear door No. 2 service hole cover.

  10. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. B006ZDE

      Disengage the 3 claws to remove the rear door inside handle sub-assembly.

  11. REMOVE REAR SPEAKER ASSEMBLY

    Click here

  12. REMOVE REAR DOOR FRAME GARNISH


    1. B0071OK

      Disengage the 2 claws to remove the rear door frame garnish.

  13. REMOVE REAR DOOR SERVICE HOLE COVER


    1. B006YYG

      Disconnect the connector.

    2. Disengage the 2 clamps.

    3. B0070B6

      Disengage the 8 clips to remove the rear door service hole cover.

  14. REMOVE REAR DOOR NO. 1 VENT SEAL


    1. B0071LD

      Remove the rear door No. 1 vent seal.

  15. REMOVE REAR DOOR PANEL PROTECTOR


    1. B006ZH7

      Disengage the clip.

    2. B006YC2

      Remove the rear door panel protector.

  16. REMOVE REAR DOOR GLASS RUN


    1. B006ZE3

      Remove the rear door glass run.

  17. REMOVE REAR DOOR CHECK ASSEMBLY


    1. B006XE2C01
      B006Z38 Nut
      B006ZY0 Bolt

      Remove the 2 nuts, bolt and rear door check assembly.

  18. REMOVE REAR DOOR WEATHERSTRIP


    1. B006ZGVC01
      *a Double-sided Tape

      Using a clip remover, disengage the 23 clips and remove the rear door weatherstrip.

  19. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. B0070A6C01
      B006Z38 Screw
      B006ZY0 Bolt

      Remove the screw, 2 bolts and rear door rear lower window frame sub-assembly.

  20. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. B0071PLC01
      B006ZFL Remove in this Direction

      Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  21. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. B006X5K

      Separate the rear door glass sub-assembly from the rear door window regulator assembly as shown in the illustration.

      Note

      After separating the rear door glass sub-assembly, do not allow it to fall.

    2. B007046C01
      B006ZFL Remove in this Direction (1)
      B006WSJ Remove in this Direction (2)

      Remove the rear door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  22. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY


    1. B0071OAC01
      *a Protective Tape

      Using a screwdriver, remove the rear door glass channel sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  23. REMOVE REAR DOOR GLASS CHANNEL FILLER


    1. Remove the rear door glass channel filler from the rear door glass sub-assembly.

  24. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY


    1. Disconnect the connector.

    2. B006XHXC01
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

    3. Remove the 3 bolts and rear door window regulator assembly.

    4. Remove the temporary bolt from the rear door window regulator assembly.

  25. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Click here

  26. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. B006Y08C01
      B006ZFL Disengage in this Direction

      Disengage the 2 claws and move the lever as shown in the illustration.

    2. B0071OBC01
      B006ZFL Remove in this Direction

      Remove the rear door outside handle assembly as shown in the illustration.

  27. REMOVE REAR DOOR OUTSIDE HANDLE COVER


    1. B0070W5

      Using a T30 "TORX" socket wrench, loosen the screw.

      Tech Tips

      The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

    2. Disengage the claw to remove the rear door outside handle cover.

  28. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD


    1. B006YMS

      Disengage the 3 claws to remove the rear door front outside handle pad.

  29. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD


    1. B006ZTC

      Disengage the claw and 3 guides to remove the rear door rear outside handle pad.

  30. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. B006XQDC01
      *A Inside
      *B Outside

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Slide the rear door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove it.

  31. REMOVE CURTAIN HOOK (w/ Rear Door Sunshade)


    1. B006XJWC01
      *a Protective Tape
      B006ZFL Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, push out the pin as shown in the illustration.

    2. B006YF9C01
      *a Protective Tape
      B006ZFL Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the pin.

    3. B006X8OC01
      B006Z38 Push

      Disengage the 4 claws to remove the 2 curtain hooks as shown in the illustration.

  32. REMOVE REAR DOOR PANEL CUSHION


    1. B006XE4

      Disengage the 4 claws to remove the 2 rear door panel cushions.

  33. REMOVE REAR DOOR NO. 2 WEATHERSTRIP


    1. B006XBG

      Disengage the 5 clips to remove the rear door No. 2 weatherstrip.

  34. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

    Click here

  35. REMOVE DOOR WINDOW FRAME MOULDING CLIP


    1. B0071HYC01
      *a Protective Tape
      B006ZFL Remove in this Direction

      Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.

  36. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

    Click here

  37. REMOVE REAR DOOR FRONT OUTSIDE SEAL


    1. B007180

      Disengage the guide to remove the rear door front outside seal.

  38. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

    Click here

  39. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

    Click here

  40. REMOVE REAR DOOR OUTSIDE STRIPE

    Click here