Click here

POWER WINDOW CONTROL SYSTEM Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH

Click here
Click here
DTC Code DTC Name
  Rear Power Window RH Auto Up / Down Function does not Operate with Rear Power Window Switch RH
Click here

DESCRIPTION

If the manual up and down functions operate normally but the auto up and down functions do not, the power window control system may be in fail-safe mode.

If power window initialization has not been performed, the auto up and down functions will not operate.

Click here

Table 1. *a Rear Power Window Regulator Switch Assembly (for RH Door) *b Power Window Regulator Motor Assembly (for Rear RH Door)
Click here

WIRING DIAGRAM

Click here

CAUTION / NOTICE / HINT

Note:

  • If the power window regulator motor assembly (for rear RH door) has been replaced with a new one, initialize the power window control system.

    Click here

  • Check that power window system customize settings "RR Window Auto Up" and "RR Window Auto Down" are set to "ON" before performing the following procedure.

    Click here

  • After the catch protection function has operated, the auto up function will not operate the first time the power window auto up switch is operated. The auto up function will operate normally after the first power window switch operation.

Tip:

If the pulse sensor built into the power window regulator motor assembly (for rear RH door) is malfunctioning, the power window control system will enter fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the rear power window regulator switch assembly (for RH door) at the auto up position, and opened manually by pushing down the rear power window regulator switch assembly (for RH door).

Click here

Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (RR-DOOR MOTOR)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / RR-Door Motor / Data List.

    5. Read the Data List according to the display on the GTS.


      1. Body Electrical > RR-Door Motor > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        RR Door P/W Auto SW Rear RH door power window auto switch signal OFF or ON

        OFF: Rear RH door power window auto up or auto down switch not being operated

        ON: Rear RH door power window auto up or auto down switch being operated

        		 -



      1. Body Electrical > RR-Door Motor > Data List
        Tester Display
        RR Door P/W Auto SW




      OK
      On the GTS screen, ON or OFF is displayed accordingly.
      Result
      Proceed to
      OK
      NG

  2. Click here

    PERFORM INITIALIZATION (for Rear RH Door)


    1. Initialize the power window regulator motor assembly (for rear RH door).

      Click here

      Result
      Proceed to
      NEXT

  3. Click here

    CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP / DOWN FUNCTION)


    1. Check that the rear RH door power window moves when the auto up and down functions of the rear power window regulator switch assembly (for RH door) are operated.

      Click here

      OK
      Rear RH door auto up and down functions are normal.
      Result
      Proceed to
      OK
      NG

    • OK

      END (PROBLEM DUE TO INITIALIZATION FAILURE)

    • NG

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)Click here

  4. Click here

    INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door)


    1. Remove the rear power window regulator switch assembly (for RH door).

      Click here

    2. Inspect the rear power window regulator switch assembly (for RH door).

      Click here

      Result
      Proceed to
      OK
      NG

  5. Click here

    CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY (for RH Door) - POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door))


    1. Disconnect the P6 power window regulator motor assembly (for rear RH door) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      P2-8 (AUTO) - P6-4 (AUTO) Always Below 1 Ω
      P2-8 (AUTO) or P6-4 (AUTO) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    • OK

      REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Door)Click here

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR