Click here

ROOF HEADLINING REASSEMBLY

Click here
Click here Click here

PROCEDURE


  1. Click here

    INSTALL NO. 1 ROOF WIRE (for Normal Roof)


    1. B006X9TC01
      *a Marking - -
      B006Y8C Butyl Tape - -

      Apply butyl tape as shown in the illustration.

      Note:

      Securely attach the butyl tape.

    2. B006YPWC01
      *A for LHD with Humidity Sensor - -
      *a Marking Tape *b 90°
      *c Adjustment Area - -
      B006ZFL Rotation Direction - -

      Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

    3. Engage each clamp.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    5. Attach the No. 1 roof wire with the butyl tape.

      Note:

      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tip:

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    6. B006ZA4C01
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 10 mm (0.394 in.) or more - -
      B006Y8C Adhesive Tape - -

      Install the No. 1 roof wire to the roof headlining with adhesive tape.

      Table 1. Adhesive Tape Size
      Area Dimension Area Dimension
      A 20 mm (0.787 in.) B 80 mm (3.15 in.) or more
      Note:

      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  2. Click here

    INSTALL NO. 1 ROOF WIRE (for Panoramic Moon Roof)


    1. B006X6BC01
      *a Marking - -
      B006Y8C Butyl Tape - -

      Apply butyl tape as shown in the illustration.

      Note:

      Securely attach the butyl tape.

    2. B007195C01
      *A for LHD with Humidity Sensor - -
      *a Marking Tape *b 90°
      *c Adjustment Area - -
      B006ZFL Rotation Direction - -

      Align the marking tape on the No. 1 roof wire with the tab on the front side of the roof headlining.

    3. Engage each clamp.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining.

    5. Attach the No. 1 roof wire with the butyl tape.

      Note:

      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tip:

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    6. B006YN0C01
      *1 No. 1 Roof Wire - -
      *a Correct *b Incorrect
      *c 10 mm (0.394 in.) or more - -
      B006Y8C Adhesive Tape - -

      Install the No. 1 roof wire to the roof headlining with adhesive tape.

      Table 2. Adhesive Tape Size
      Area Dimension Area Dimension
      A 20 mm (0.787 in.) B 80 mm (3.15 in.) or more
      Note:

      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  3. Click here

    INSTALL VANITY LIGHT ASSEMBLY

    Tip:

    Use the same procedure for the RH side and LH side.


    1. B006XGYC01
      *1 Bulb Holder
      *a Claw (A)
      *b Claw (B)

      Engage the claw (B) to install the vanity light assembly.

    2. Engage the 2 claws (A) to install the bulb holder to the vanity light assembly.

  4. Click here

    INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  5. Click here

    INSTALL NO. 4 ROOF SILENCER (for Normal Roof)


    1. B006YQIC01
      *a Hot-melt Glue *b Marking

      Align the No. 4 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.

  6. Click here

    INSTALL NO. 2 ROOF SILENCER (for Normal Roof)


    1. B007059C01
      *a Hot-melt Glue *b Marking

      Align the No. 2 roof silencer with the markings on the roof headlining and install it using hot-melt glue as shown in the illustration.