Click here

ROOF HEADLINING REMOVAL

Click here
Click here Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during roof headlining removal/installation are shown below.

Table 1. Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here
CAUTION:
B0071E9

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here

Click here

PROCEDURE


  1. Click here

    REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

    Click here

  2. Click here

    REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

    Click here

  3. Click here

    REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)

    Click here

  4. Click here

    REMOVE REAR SEAT ASSEMBLY (for Reclining Seat Type)

    Click here

  5. Click here

    REMOVE FRONT DOOR SCUFF PLATE LH


    1. B006YV6C01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the claw as shown in the illustration.

      Tip:

      Use the same procedure for the front side and rear side.

    2. B0071E3C01
      B006ZFL Remove in this Direction

      Disengage the 8 claws and guide to remove the front door scuff plate LH as shown in the illustration.

  6. Click here

    REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. B006ZP4C01
      B006ZFL Remove in this Direction

      Remove the clip.

    2. Disengage the claw and clip to remove the cowl side trim sub-assembly LH as shown in the illustration.

  7. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  8. Click here

    REMOVE FRONT PILLAR GARNISH LH


    1. B0071PYC01
      B006Y8C Protective Tape

      Apply protective tape around the front pillar garnish LH as shown in the illustration.

    2. B0071DXC01
      *1 Front Pillar Garnish Clip
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.

      Tip:

      Let the front pillar garnish LH hang from the front pillar garnish clip.

    3. B0070RMC01
      *1 Front Pillar Garnish Clip
      B006ZFL Remove in this Direction

      While pushing the tabs of the front pillar garnish clip as shown in the illustration, disengage it.

      Note:

      • The front pillar garnish clip is reusable if it is not damaged.

      • If the front pillar garnish clip is damaged, replace it with a new one.

      Tip:

      When the front pillar garnish clip cannot be disengaged easily:


      1. B006ZAXC01
        B006ZFL Move in this Direction

        While pushing the tab of the front pillar garnish clip shown in the illustration with your finger, move the front pillar garnish clip in the direction shown in the illustration.

      2. B006XH3C01
        B006ZFL Pull in this Direction

        While pulling the front pillar garnish clip as shown in the illustration, push the tab of the front pillar garnish clip shown in the illustration with a screwdriver and disengage the front pillar garnish clip.

    4. w/o Front No. 3 Speaker:


      1. B0070PKC01
        B006ZFL Remove in this Direction

        Disengage the 2 guides to remove the front pillar garnish LH as shown in the illustration.

    5. w/ Front No. 3 Speaker:


      1. Disengage the 2 guides as shown in the illustration.

      2. Disconnect the connector to remove the front pillar garnish LH.

    6. Remove the clip from the front pillar garnish LH.

    7. B0070TJC01
      *1 Curtain Shield Airbag Assembly LH
      *a Protective Cover
      *b Adhesive Tape

      Protect the curtain shield airbag assembly LH.


      1. Cover the curtain shield airbag assembly LH with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.

        Note:

        Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  9. Click here

    REMOVE REAR DOOR SCUFF PLATE LH


    1. B0071ELC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the claw as shown in the illustration.

    2. B006X4QC01
      B006ZFL Remove in this Direction

      Disengage the 5 claws and guide to remove the rear door scuff plate LH as shown in the illustration.

  10. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

    Click here

  11. Click here

    REMOVE LAP BELT OUTER ANCHOR COVER (for LH Side)

    Click here

  12. Click here

    DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

    Click here

  13. Click here

    REMOVE LOWER CENTER PILLAR GARNISH LH


    1. B006XLUC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the 2 claws as shown in the illustration.

    2. B006XJSC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the 3 clips to remove the lower center pillar garnish LH as shown in the illustration.

  14. Click here

    REMOVE UPPER CENTER PILLAR GARNISH LH


    1. B006X7Q

      Using a clip remover, remove the 2 clips.

    2. B006XENC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the guide as shown in the illustration.

    3. B006ZJDC01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the clip and 2 guides to remove the upper center pillar garnish LH as shown in the illustration.

    4. Remove the clip from the upper center pillar garnish LH.

  15. Click here

    REMOVE INNER ROOF SIDE GARNISH LH


    1. B006ZG5C01
      B006XFD Place Hand Here
      B006ZFL Remove in this Direction

      Disengage the 3 clips as shown in the illustration.

    2. B006YA4C01
      B006ZFL Remove in this Direction

      Disengage the 2 guides to remove the inner roof side garnish LH as shown in the illustration.

    3. Remove the 3 clips from the inner roof side garnish LH.

  16. Click here

    REMOVE FRONT DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side.

  17. Click here

    REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  18. Click here

    REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure as for the LH side.

  19. Click here

    REMOVE FRONT PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  20. Click here

    REMOVE REAR DOOR SCUFF PLATE RH

    Tip:

    Use the same procedure as for the LH side.

  21. Click here

    REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tip:

    Use the same procedure as for the LH side.

  22. Click here

    REMOVE LAP BELT OUTER ANCHOR COVER (for RH Side)

    Tip:

    Use the same procedure as for the LH side.

  23. Click here

    DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  24. Click here

    REMOVE LOWER CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  25. Click here

    REMOVE UPPER CENTER PILLAR GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  26. Click here

    REMOVE INNER ROOF SIDE GARNISH RH

    Tip:

    Use the same procedure as for the LH side.

  27. Click here

    REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  28. Click here

    REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY

    for UA80E:

    Click here

    for UB80E:

    Click here

    for U760E:

    Click here

  29. Click here

    REMOVE ROOF CONSOLE BOX ASSEMBLY

    Click here

  30. Click here

    REMOVE SPOT LIGHT ASSEMBLY

    Click here

  31. Click here

    REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

    Click here

  32. Click here

    REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ Cover)

    Click here

  33. Click here

    REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-collision System)

    Click here

  34. Click here

    REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-collision System)

    Click here

  35. Click here

    REMOVE ASSIST GRIP ASSEMBLY

    Tip:

    Use the same procedure for all assist grip assemblies.


    1. B006ZG1C01
      *a Cutout

      Insert SST into the cutout of the assist grip cover LH as shown in the illustration.

      09813-00010
      Note:

      To prevent the assist grip assembly from being damaged, make sure to insert SST straight into the cutout.

    2. B0071LJC01
      *a 30 to 45°
      B006ZFL Remove in this Direction

      Pull SST as shown in the illustration to disengage the claw.

      Note:

      To prevent the assist grip assembly from being damaged, make sure to only pull SST as shown in the illustration.

      Tip:

      Use the same procedure for the claw on the other side of the assist grip cover LH.

    3. Remove the assist grip cover LH.

      Tip:

      Use the same procedure for the LH side and RH side.

    4. B006Z1GC01
      B006ZFL Remove in this Direction

      Disengage the 2 clips as shown in the illustration to remove the assist grip assembly.

    5. Remove the 2 clips from the vehicle body.

  36. Click here

    REMOVE REAR ASSIST GRIP ASSEMBLY LH

    Tip:

    Use the same procedure as for the assist grip assembly.

  37. Click here

    REMOVE REAR ASSIST GRIP ASSEMBLY RH

    Tip:

    Use the same procedure as for the assist grip assembly.

  38. Click here

    REMOVE VISOR BRACKET COVER LH


    1. B006ZIWC01
      B006XFD Insert Moulding Remover Here

      Using a moulding remover, disengage the 4 claws as shown in the illustration and remove the visor bracket cover LH.

  39. Click here

    REMOVE VISOR ASSEMBLY LH


    1. for "TORX" Screw:


      1. B0070LW

        Using a T25 "TORX" socket wrench, remove the 2 screws.

    2. except "TORX" Screw:


      1. Remove the 2 screws.

    3. B006WW8C01
      *1 Visor Holder LH
      B006ZFL Remove in this Direction (1)
      B006WSJ Remove in this Direction (2)

      Pull the visor assembly LH in the direction indicated by the arrow (1) shown in the illustration to disconnect it from the visor holder LH.

    4. Pull the visor assembly LH in the direction indicated by the arrow (2) shown in the illustration to remove it.

  40. Click here

    REMOVE VISOR HOLDER LH


    1. B006Y6CC02
      *a 45°
      B006ZFL Remove in this Direction (1)
      B006WSJ Remove in this Direction (2)

      Turn the visor holder LH approximately 45° and pull it out as indicated by the arrows, in the order shown in the illustration.

    2. Disengage the 2 claws to remove the visor holder LH.

  41. Click here

    REMOVE VISOR BRACKET COVER RH

    Tip:

    Use the same procedure as for the LH side.

  42. Click here

    REMOVE VISOR ASSEMBLY RH

    Tip:

    Use the same procedure as for the LH side.

  43. Click here

    REMOVE VISOR HOLDER RH

    Tip:

    Use the same procedure as for the LH side.

  44. Click here

    REMOVE ROOF HEADLINING ASSEMBLY


    1. for Windshield Glass Side:


      1. Disconnect each connector.

    2. for Front Pillar LH Side:


      1. B006ZG8C01
        *A w/ Pre-collision System

        Remove the protective cover.

      2. Disconnect each connector.

      3. Using a clip remover, disengage the 4 clamps.

      4. Install the protective cover.

    3. for Front Pillar RH Side:


      1. B006XY5C01
        *a Guide
        *b Clamp

        Remove the protective cover.

      2. Remove the bolt.

      3. Disengage the guide to disconnect the connector bracket.

      4. Using a clip remover, disengage the 2 clamps.

      5. Install the protective cover.

    4. for Rear Pillar LH Side:


      1. B007018

        Disconnect the connector.

      2. Using a clip remover, disengage the clamp.

    5. for Rear Pillar RH Side:


      1. B006YODC04
        *A w/ Digital Audio Broadcasting Antenna

        Disconnect each connector.

      2. Using a clip remover, disengage each clamp.

    6. for Roof Side (for Normal Roof):


      1. B006Y85C01
        *A w/ Digital Television Antenna - -
        B006ZFL Remove in this Direction - -

        Using a clip remover, remove the 2 clips.

      2. w/ Digital Television Antenna:


        1. Disconnect the connector.

      3. Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

        Tip:

        Leave the 2 clips installed the vehicle body.

    7. for Roof Side (for Panoramic Moon Roof):


      1. B00718LC01
        *A w/ Digital Television Antenna - -
        *a Fastener *b Guide
        B006ZFL Remove in this Direction - -

        Using a clip remover, remove the 2 clips.

      2. Disconnect each connector.

      3. Disengage the 14 fasteners and guide.

      4. Slide the roof headlining assembly to disengage it from the 2 clips as shown in the illustration.

        Tip:

        Leave the 2 clips installed the vehicle body.

    8. B007077C01
      B006ZFL Remove in this Direction - -

      Remove the roof headlining assembly from the vehicle through the front door RH as shown in the illustration.

      Note:

      Do not damage the roof headlining assembly or vehicle interior.

    9. B006X68C01
      B006ZFL Remove in this Direction

      Remove the 2 clips from the vehicle body as shown in the illustration.