SEAT BELT WARNING SYSTEM(w/o Occupant Classification System) ON-VEHICLE INSPECTION

PROCEDURE


  1. INSPECT DRIVER SEAT BELT WARNING SYSTEM

    Tech Tips

    The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


    1. w/ Buzzer Regulated by Law


      1. Turn the ignition switch to ON.

      2. When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

        Check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

      3. Lift the vehicle using a swing arm type lift.

        Click here

      4. Start the engine.

      5. Check the state of the seat belt warning light on the combination meter assembly under the following conditions:


        1. Step 1:

          When the driver seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

        2. Step 2:

          When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

          After 2 minutes, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        3. Step 3:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        4. Step 4:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        5. Step 5:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

    2. w/o Buzzer Regulated by Law


      1. Turn the ignition switch to ON.

      2. When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.

      3. Lift up the vehicle using a swing arm type lift.

        Click here

      4. Start the engine.

      5. When the driver seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.

      6. When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

        After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 90 seconds and then illuminates.

      7. When the driver seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

  2. INSPECT FRONT PASSENGER SEAT BELT WARNING SYSTEM (w/ Front Passenger Seat Belt Warning System)

    Tech Tips

    The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


    1. w/ Buzzer Regulated by Law


      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.

        Note

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. Fasten the driver seat belt.

      3. Turn the ignition switch to ON.

      4. When the front passenger seat belt is not fastened with the front passenger seat occupied, check that the seat belt warning light on the combination meter assembly blinks for 6 seconds.

        Check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

      5. Lift the vehicle using a swing arm type lift.

        Click here

      6. Start the engine.

      7. Check the state of the seat belt warning light on the combination meter assembly under the following conditions:


        1. Step 1:

          When the front passenger seat belt is not fastened, the shift lever is in any position other than P and the parking brake is released, check that the seat belt warning light on the combination meter assembly blinks.

        2. Step 2:

          When the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks.

          After 2 minutes, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        3. Step 3:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the shift lever is moved to P, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        4. Step 4:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the parking brake is applied, check that the seat belt warning light on the combination meter assembly changes from blinking to illuminated.

        5. Step 5:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, with the front passenger seat belt not fastened and the weight on the front passenger seat, check that the seat belt warning light on the combination meter assembly turns off when the weight is removed from the front passenger seat.

        6. Step 6:

          Starting from step 1 with the seat belt warning light on the combination meter assembly blinking, when the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

    2. w/o Buzzer Regulated by Law


      1. Turn the ignition switch to ON.

      2. Place a weight of 20 kg (44.0 lb) on the front passenger seat.

        Note

        Place the weight on the seat cushion and do not allow it to come into contact with the seatback.

      3. Fasten the driver seat belt.

      4. When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter assembly illuminates.

      5. Lift the vehicle using a swing arm type lift.

        Click here

      6. Start the engine.

      7. When the front passenger seat belt is not fastened, the parking brake is released and the vehicle is driven at approximately 1.75 km/h (1 mph) or more, check that seat belt warning light on the combination meter blinks at an interval of 1.2 seconds.

      8. When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter assembly blinks at an interval of 1.2 seconds for 30 seconds.

        After that, check that the seat belt warning light on the combination meter assembly blinks at an interval of 0.4 seconds for 90 seconds and then illuminates.

      9. When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter assembly turns off.

  3. INSPECT REAR SEAT BELT WARNING LIGHT (w/ Rear Seat Belt Warning)


    1. B006Z61C03
      *1 Rear Seat Belt Warning Light (Telltale Light Assembly)
      *a LH
      *b Center
      *c RH

      Check the state of the rear seat belt warning light on the telltale light assembly:


      1. Turn the ignition switch off.

      2. Open and then close either rear door.

      3. Turn the ignition switch to ON.

      4. When a rear seat belt is not fastened, check that the rear seat belt warning light on the telltale light assembly is illuminated.

      5. After 30 seconds, check that the rear seat belt warning light on the telltale light assembly turns off.

      6. When one of the rear seat belts is unfastened from being fastened, check that the rear seat belt warning light on the telltale light assembly illuminates.

  4. INSPECT SEAT BELT WARNING BUZZER

    Tech Tips

    The seat belt warning buzzer can be customized. Make sure that this function is ON.

    Click here


    1. for Front Seat Belt Warning Buzzer (w/ Buzzer Regulated by Law):


      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.

        Note

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. After turning the ignition switch to ON, wait for approximately 1.8 seconds with the driver seat belt not fastened check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.

      3. Lift the vehicle using a swing arm type lift.

        Click here

      4. Start the engine.

      5. When the driver or front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds once.

      6. When 24 seconds have passed after the buzzer sounded, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 6 seconds.

      7. After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.

      8. Check that the seat belt warning buzzer in the combination meter assembly stops 96 seconds after it started sounding at an interval of 1.2 seconds.

      9. After the seat belt warning buzzer in the combination meter assembly stops, turn the ignition switch off and then start the engine. Drive the vehicle at approximately 20 km/h (12 mph) or more with either the driver or front passenger seat belt not fastened and check that the buzzer sounds in the same pattern again.

      10. After the seat belt warning buzzer in the combination meter assembly stops, fasten the driver or front passenger seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the driver or front passenger seat belt and check that the buzzer sounds in the same pattern again.

    2. for Front Seat Belt Warning Buzzer (w/o Buzzer Regulated by Law):


      1. Place a weight of 20 kg (44.0 lb) on the front passenger seat.*

        Note

        Place the weight on the seat cushion and allow it to come into contact with the seatback.

      2. Lift the vehicle using a swing arm type lift.

        Click here

      3. Start the engine.

      4. When the driver or front passenger seat belt* is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 1.2 seconds for 30 seconds.

      5. After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 90 seconds.

      6. Check that the seat belt warning buzzer in the combination meter assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.

      7. After the seat belt warning buzzer in the combination meter assembly stops, turn the ignition switch off and then start the engine. Drive the vehicle at approximately 20 km/h (12 mph) or more with either the driver or front passenger seat belt* not fastened and check that the buzzer sounds in the same pattern again.

      8. After the seat belt warning buzzer in the combination meter assembly stops, fasten the driver or front passenger seat belt*, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the driver or front passenger seat belt* and check that the buzzer sounds in the same pattern again.


        • *: w/ Front Passenger Seat Belt Warning System

    3. for Rear Seat Belt Warning Buzzer*:


      1. Open and close either rear door.

      2. Lift the vehicle using a swing arm type lift.

        Click here

      3. Fasten the driver seat belt.

      4. Start the engine.

      5. Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the seat belt warning buzzer in the combination meter assembly sounds once.

      6. After the seat belt warning buzzer sounds once, check that it sounds at an interval of 1.2 seconds for 6 seconds.

      7. After the seat belt warning buzzer has been sounding for 6 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter assembly sounds at an interval of 0.4 seconds for 30 seconds.

      8. Check that the seat belt warning buzzer in the combination meter assembly stops 36 seconds after it started sounding at an interval of 1.2 seconds.

      9. After the seat belt warning buzzer in the combination meter assembly stops, turn the ignition switch off, open and close either rear door and then start the engine. Fasten and unfasten a rear seat belt then drive the vehicle at approximately 20 km/h (12 mph) or more and check that the buzzer sounds in the same pattern again.

      10. After the seat belt warning buzzer in the combination meter assembly stops, fasten a rear seat belt, drive the vehicle at approximately 20 km/h (12mph) or more, unfasten the rear seat belt and check that the buzzer sounds in the same pattern again.


        • *: w/ Rear Seat Belt Warning