REAR CENTER SEAT OUTER BELT ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear center seat outer belt assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • B0071E9

    Be sure to read Precaution thoroughly before servicing.

    Click here

PROCEDURE


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an airbag deploys for any reason, it may cause a serious injury.

    B006XLM

  3. REMOVE REAR SEAT ASSEMBLY (for Fixed Seat Type)

    Click here

  4. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fixed Seat Type)

    Click here

  5. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fixed Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  6. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

    Click here

  7. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

    Click here

  8. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

    Click here

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Fold Down Seat Type)

    Click here

  10. REMOVE REAR SIDE SEATBACK ASSEMBLY LH (for Fold Down Seat Type)

    Click here

  11. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Fold Down Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE REAR SIDE SEATBACK ASSEMBLY RH (for Fold Down Seat Type)

    Tech Tips

    Use the same procedure as for the LH side.

  13. REMOVE REAR SEAT ASSEMBLY (for Reclining Seat Type)

    Click here

  14. REMOVE INNER ROOF SIDE GARNISH LH

    Click here

  15. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY LH

    Click here

  17. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  18. REMOVE CENTER STOP LIGHT SET (w/o Rear Sunshade)

    Click here

  19. REMOVE REAR SEAT SHOULDER BELT HOLE COVER

    Click here

  20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/o Rear Sunshade)

    Click here

  21. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Rear Sunshade)

    Click here

  22. REMOVE REAR CENTER SEAT OUTER BELT ASSEMBLY


    1. B006YHT

      Remove the 2 bolts.

    2. Disengage the guide to remove the rear center seat outer belt assembly.

  23. REMOVE SEAT BELT RETRACTOR COVER


    1. B006WW0C01
      B006ZFL Remove in this Direction

      Remove the seat belt retractor cover as shown in the illustration.