FRONT SEAT ASSEMBLY(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY


    1. B006YZG

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the front seat airbag assembly connector under the front seat assembly.


      1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

        B006X59C01
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly.

    4. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    5. Temporarily install the front seat assembly with the 4 bolts.

    6. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    7. B006WW9N01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    8. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    9. B006YD1N01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. B00700U

      Engage the 2 claws and guide to install the rear inner seat track bracket cover.

  3. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. B00703P

      Engage the 2 claws and guide to install the rear outer seat track bracket cover.

  4. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    2. B0070IX

      Engage the 2 claws to install the front inner seat track bracket cover.

  5. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. B006YAD

      Engage the 2 claws to install the front outer seat track bracket cover.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly.

  7. INSPECT FRONT SEAT ASSEMBLY


    1. w/ Seat Position Memory System:

      Click here

    2. w/o Seat Position Memory System:

      Click here

  8. CHECK SEAT HEATER

    Click here

  9. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here