FRONT SEAT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here


  • Position control ECU assembly (driver seat)

  • Front seatback frame sub-assembly (driver seat)

  • Front seat adjuster assembly (driver seat)

 Initialize position control ECU Front power seat control system

Click here

CAUTION:


  • Be sure to read Precaution thoroughly before servicing. (w/ Front Seat Side Airbag)

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

If the front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage. (w/ Front Seat Side Airbag)

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. Remove the front seat headrest assembly from the front seat assembly.

  3. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    2. B006YAD

      Disengage the 2 claws to remove the front outer seat track bracket cover.

  4. REMOVE FRONT INNER SEAT TRACK BRACKET COVER


    1. B0070IX

      Disengage the 2 claws to remove the front inner seat track bracket cover.

  5. REMOVE REAR OUTER SEAT TRACK BRACKET COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    2. B00703P

      Disengage the 2 claws and guide to remove the rear outer seat track bracket cover.

  6. REMOVE REAR INNER SEAT TRACK BRACKET COVER


    1. B00700U

      Disengage the 2 claws and guide to remove the rear inner seat track bracket cover.

  7. REMOVE FRONT SEAT ASSEMBLY (w/o Front Seat Side Airbag)


    1. B006YD1

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.

    2. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    3. B006WW9

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.

    4. Operate the reclining power seat switch knob and move the seatback to the upright position.

    5. Operate the slide and vertical power seat switch knob and move the front seat assembly to the center position.

    6. w/ Vertical Adjuster:


      1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the uppermost position.

    7. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. Disconnect each connector and disengage each clamp under the front seat assembly.

    9. B006YZG

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.

  8. REMOVE FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)


    1. B006YD1

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the rear side of the front seat assembly.

    2. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    3. B006WW9

      Using a T50 "TORX" socket wrench, remove the 2 bolts on the front side of the front seat assembly.

    4. Operate the reclining power seat switch knob and move the seatback to the upright position.

    5. Operate the slide and vertical power seat switch knob and move the front seat assembly to the center position.

    6. w/ Vertical Adjuster:


      1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the uppermost position.

    7. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    8. Disconnect the front seat airbag assembly connector under the front seat assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. B006YOUC04
        *a White Housing Lock
        *b Yellow CPA
        B006ZFL Slide in this Direction

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting the connector.

    9. Disconnect each connector and disengage each clamp under the front seat assembly.

    10. B006YZG

      Remove the front seat assembly.

      Note

      Be careful not to damage the vehicle body.