FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing. (w/ Front Seat Side Airbag)

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The following procedure is for LHD vehicles.

  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY (w/o Front Seat Side Airbag)


    1. B0071OT

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect each connector and engage each clamp under the front seat assembly.

    3. Temporarily install the front seat assembly with the 4 bolts.

    4. Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

    5. B006XZUN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    6. Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

    7. B006Z2UN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSTALL FRONT SEAT ASSEMBLY (w/ Front Seat Side Airbag)


    1. B0071OT

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the front seat airbag assembly connector under the front seat assembly.


      1. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

        B006X59C05
        *a Correct *b Incorrect
        *c Yellow CPA *d White Housing Lock

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly.

    4. Temporarily install the front seat assembly with the 4 bolts.

    5. Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

    6. B006XZUN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    7. Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

    8. B006Z2UN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  3. INSPECT SEAT SLIDE ADJUSTER LOCK


    1. While performing a sliding operation of the front seat assembly, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly installation bolts and adjust the adjuster position.

  4. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. Operate the seat track adjusting handle and move the front seat assembly to the foremost position.

    2. B006ZWR

      Engage the 2 claws and guide to install the rear inner seat track bracket cover.

  5. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. B006XYM

      Engage the 2 claws and guide to install the rear outer seat track bracket cover.

  6. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the seat track adjusting handle and move the front seat assembly to the rearmost position.

    2. B00714F

      Engage the 2 claws to install the front inner seat track bracket cover.

  7. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. B0071K9

      Engage the 2 claws to install the front outer seat track bracket cover.

  8. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly.

  9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Front Seat Side Airbag)

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  10. CHECK SEAT HEATER (w/ Seat Heater System)

    Click here

  11. PERFORM DIAGNOSTIC SYSTEM CHECK (w/ Front Seat Side Airbag)

    Click here

  12. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (w/ Occupant Classification System)

    Click here