FRONT SEAT ASSEMBLY(for Manual Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY RH


    1. B004LT9

      Place the front seat assembly RH in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the front seat airbag assembly RH connector under the front seat assembly RH.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B006X59C01
        *a Correct *b Incorrect
        *c Yellow CPA - -

      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly RH.

    4. Temporarily install the front seat assembly RH with the 4 bolts.

    5. Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.

    6. B004INHN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the front side of the front seat assembly RH.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    7. Operate the seat track adjusting handle and move the front seat assembly RH to the foremost position.

    8. B004MSLN01

      Using a T50 "TORX" socket wrench, tighten the 2 bolts on the rear side of the front seat assembly RH.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSPECT SEAT SLIDE ADJUSTER LOCK


    1. While performing a sliding operation of the front seat assembly RH, check that the left and right adjusters move together smoothly and lock simultaneously. If the seat adjusters do not lock simultaneously, loosen the front seat assembly RH installation bolts and adjust the adjuster position.

  3. INSTALL REAR INNER SEAT TRACK BRACKET COVER RH


    1. Operate the seat track adjusting handle and move the front seat assembly RH to the foremost position.

    2. B004IKK

      Engage the 2 claws and guide to install the rear inner seat track bracket cover RH.

  4. INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH


    1. B004ODD

      Engage the 2 claws and guide to install the rear outer seat track bracket cover RH.

  5. INSTALL FRONT INNER SEAT TRACK BRACKET COVER RH


    1. Operate the seat track adjusting handle and move the front seat assembly RH to the rearmost position.

    2. B004NH5

      Engage the 2 claws to install the front inner seat track bracket cover RH.

  6. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH


    1. B004OB7

      Engage the 2 claws to install the front outer seat track bracket cover RH.

  7. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly RH.

  8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  9. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  10. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK

    Click here