FRONT PASSENGER AIRBAG ASSEMBLY REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel passenger airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B0071NY

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

    Click here

  3. DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B006YQGC01
      *a Slider
      B006ZFL Release in this Direction

      Slide the slider to release the lock, and then disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  4. DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B0070QTC01
      *a Slider
      B006ZFL Release in this Direction

      Slide the slider to release the lock, and then disconnect the connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  5. REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here

  6. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/o Occupant Classification System)

    CAUTION:

    When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

    B006WY7C02
    B006Y8C Deployment Side

    1. B006ZR1

      Remove the 2 screws and disengage the clamp.

    2. B0070YGC01
      *a Passenger Airbag Door Retainer
      B006ZFL Move the screwdriver in this Direction

      Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.

      Note

      Do not damage the deployment surface of the instrument panel passenger airbag assembly.

    3. B007131

      Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

  7. REMOVE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (w/ Occupant Classification System)

    CAUTION:

    When storing the instrument panel passenger airbag assembly, keep the airbag deployment side facing upward.

    B006WY7C02
    B006Y8C Deployment Side

    1. B006Y1M

      Remove the 2 screws and disengage the clamp.

    2. B006Y34C01
      *a Passenger Airbag Door Retainer
      B006ZFL Move the screwdriver in this Direction

      Using a screwdriver, pry back the passenger airbag door retainer to disengage the 3 hooks as shown in the illustration.

      Note

      Do not damage the deployment surface of the instrument panel passenger airbag assembly.

    3. B007196

      Disengage the 3 hooks to remove the instrument panel passenger airbag assembly from the instrument panel safety pad sub-assembly.

  8. REMOVE NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)


    1. B006YX4C01
      *a Protective Tape
      *b Airbag Connector
      *c Airbag Connector Locking Button
      B006ZFL Release in this Direction

      Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.

    2. Disconnect the airbag connector to remove the No. 5 instrument panel wire from the instrument panel passenger airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  9. REMOVE NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)


    1. B0070C7C01
      *a Protective Tape
      *b Airbag Connector
      *c Airbag Connector Locking Button
      B006ZFL Release in this Direction

      Using a screwdriver with its tip wrapped with protective tape, release the 2 airbag connector locking buttons.

    2. Disconnect the 2 airbag connectors to remove the No. 5 instrument panel wire from the instrument panel passenger airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.