KNEE AIRBAG ASSEMBLY(for Driver Side) INSTALLATION

PROCEDURE


  1. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B006YS3C01
      *a Airbag Connector
      *b Airbag Connector Locking Button
      B006ZFL Push in this Direction

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector locking button to install the airbag connector.

    5. B006XU1

      Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    6. Engage the 2 claws.

    7. Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  2. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B006WXVC02
      *a Airbag Connector
      *b Airbag Connector Locking Button
      B006ZFL Push in this Direction

      Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the airbag connector locking button to install the airbag connector.

    5. B006YAS

      Engage the 2 hooks to temporarily install the lower No. 1 instrument panel airbag assembly.

    6. Engage the 2 claws.

    7. Install the lower No. 1 instrument panel airbag assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 1 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  3. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    Click here

  4. INSTALL NO. 1 METER HOOD CLUSTER

    Click here

  5. INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  6. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  7. INSTALL NO. 2 METER HOOD CLUSTER

    Click here

  8. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

    Click here

  9. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

    Click here

  10. INSTALL INSTRUMENT SIDE PANEL

    Click here

  11. CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

  12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY

    Click here

  13. INSTALL FRONT DOOR SCUFF PLATE

    Click here

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  15. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  16. INSPECT SRS WARNING LIGHT

    Click here