KNEE AIRBAG ASSEMBLY(for Driver Side) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during lower No. 1 instrument panel airbag assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    B0071NY

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    B006XLM

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY

    Click here

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

    Tech Tips

    Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.

  6. REMOVE INSTRUMENT SIDE PANEL

    Click here

  7. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

    Click here

  8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

    Click here

  9. REMOVE NO. 2 METER HOOD CLUSTER

    Click here

  10. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  11. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

    Click here

  12. REMOVE NO. 1 METER HOOD CLUSTER

    Click here

  13. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    Click here

  14. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for LHD)

    CAUTION:

    When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

    B006Z09C02
    B006Y8C Deployment Side

    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B006Y8U

      Remove the 4 bolts.

    4. B006YQK

      Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.

      Note

      When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. B006ZO6C01
      *a Protective Tape
      *b Airbag Connector
      *c Airbag Connector Locking Button
      B006ZFL Release in this Direction

      Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.

    6. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  15. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for RHD)

    CAUTION:

    When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.

    B006Z09C02
    B006Y8C Deployment Side

    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      B006XLM
    3. B006YCJ

      Remove the 4 bolts.

    4. B0071D3

      Disengage the 2 claws and separate the lower No. 1 instrument panel airbag assembly.

      Note

      When separating the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. B006X1SC02
      *a Protective Tape
      *b Airbag Connector
      *c Airbag Connector Locking Button
      B006ZFL Release in this Direction

      Using a screwdriver with its tip wrapped with protective tape, release the airbag connector locking button.

    6. Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.