OCCUPANT CLASSIFICATION SYSTEM, Diagnostic DTC:B1780

DTC Code DTC Name
B1780 Front Occupant Classification Sensor LH Circuit Malfunction

DESCRIPTION

The front occupant classification sensor LH circuit consists of the occupant detection ECU and front occupant classification sensor LH.

DTC B1780 is stored when a malfunction is detected in the front occupant classification sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1780 Front Occupant Classification Sensor LH Circuit Malfunction

  • The occupant detection ECU detects a line short, short to ground or B+, or an open in the front occupant classification sensor LH circuit.

  • Front occupant classification sensor LH malfunction

  • Occupant detection ECU malfunction

  • Front seat wire RH

  • Front occupant classification sensor LH (Front seat adjuster assembly RH)*

  • Occupant detection ECU

WIRING DIAGRAM

B006Y54E05

CAUTION / NOTICE / HINT

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

Tech Tips


  • When DTC B1650 is stored as a result of troubleshooting for the airbag system, check the DTCs stored in the occupant detection ECU. When DTC B1780 is output, perform troubleshooting for this DTC first.

  • If it is difficult to perform troubleshooting (wire harness inspection), remove the front passenger seat installation bolts to see under the seat cushion.

  • In the above case, lift and hold the seat so that it does not fall down. Hold the seat only as necessary because holding the seat for a long period of time may cause seat rail deformation.

PROCEDURE


  1. CHECK CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

    3. Check that the connectors are properly connected to the occupant detection ECU and front occupant classification sensor LH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the occupant detection ECU and front occupant classification sensor LH.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT WIRE RH

    OK

  2. CHECK FRONT SEAT WIRE RH


    1. B006Y1NC17
      *1 Front Occupant Classification Sensor LH
      *2 Occupant Detection ECU
      *3 Front Seat Wire RH
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Occupant Detection ECU)
      *b

      Front view of wire harness connector

      (to Front Occupant Classification Sensor LH)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      a19-1 (SVC1) - Body ground Ignition switch ON Below 1 V
      a19-3 (SIG1) - Body ground Ignition switch ON Below 1 V
      a19-5 (SGD1) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

    6. Using service wires, connect terminals 1 (SVC) and 3 (SGD), and terminals 2 (SIG) and 3 (SGD) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      a19-1 (SVC1) - a19-5 (SGD1) Always Below 1 Ω
      a19-3 (SIG1) - a19-5 (SGD1) Always Below 1 Ω

    8. Disconnect the service wires from connector C.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      a19-1 (SVC1) - a19-5 (SGD1) Always 1 MΩ or higher
      a19-3 (SIG1) - a19-5 (SGD1) Always 1 MΩ or higher
      a19-1 (SVC1) - a19-3 (SIG1) Always 1 MΩ or higher
      a19-1 (SVC1) - Body ground Always 1 MΩ or higher
      a19-3 (SIG1) - Body ground Always 1 MΩ or higher
      a19-5 (SGD1) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT WIRE RH

    OK

  3. CHECK DTC


    1. Connect the connectors to the occupant detection ECU and front occupant classification sensor LH.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in the occupant detection ECU.


      Body Electrical > Occupant Detection > Clear DTCs

    5. Clear the DTCs stored in the airbag sensor assembly.


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 10 seconds.

    8. Check for DTCs.


      Body Electrical > Occupant Detection > Trouble Codes
      OK
      DTC B1780 is not output.

      Tech Tips

      Codes other than DTC B1780 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  4. CHECK OCCUPANT DETECTION ECU


    1. Disconnect the cable from the negative (-) battery terminal.

    2. Replace the occupant detection ECU with a known good one.

      Click here

      Tech Tips

      Perform the following inspection using known good parts from another vehicle if possible.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in the occupant detection ECU.


      Body Electrical > Occupant Detection > Clear DTCs

    6. Clear the DTCs stored in the airbag sensor assembly.


      Body Electrical > SRS Airbag > Clear DTCs

    7. Turn the ignition switch off.

    8. Turn the ignition switch to ON, and wait for at least 10 seconds.

    9. Check for DTCs.


      Body Electrical > Occupant Detection > Trouble Codes
      OK
      DTC B1780 is not output.

      Tech Tips

      Codes other than DTC B1780 may be output at this time, but they are not related to this check.

    10. Turn the ignition switch off.

    11. Disconnect the cable from the negative (-) battery terminal.

    12. Restore the occupant detection ECU that was installed for testing to its original location.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH Click here

    OK

  5. REPLACE OCCUPANT DETECTION ECU


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

    3. Replace the occupant detection ECU with a new one.

      Click here

    4. Connect the cable to the negative (-) battery terminal.

      Result
      Proceed to
      NEXT

    NEXT

  6. PERFORM ZERO POINT CALIBRATION


    1. Using the GTS, perform Zero Point Calibration.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END

  7. REPLACE FRONT SEAT ADJUSTER ASSEMBLY RH


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

    3. Replace the front seat adjuster assembly RH.

      Click here

    4. Connect the cable to the negative (-) battery terminal.

      Result
      Proceed to
      NEXT

    NEXT

  8. PERFORM ZERO POINT CALIBRATION


    1. Using the GTS, perform Zero Point Calibration.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    END