AIRBAG SYSTEM SRS Warning Light Remains ON

DESCRIPTION

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then turns off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

If a malfunction occurs in the airbag sensor assembly, combination meter assembly or wire harness connected to the airbag sensor assembly or combination meter assembly, the SRS warning light comes on.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically turns off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly via CAN communication.

WIRING DIAGRAM

B006WRPE73

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK SRS WARNING LIGHT OPERATION


    1. Turn the ignition switch to ON and check the SRS warning light condition.

      Tech Tips

      The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.

      Result
      Result Proceed to
      After the primary check period, the SRS warning light remains on. A
      After the primary check period, the SRS warning light turns off and comes on again. B

    B

    CHECK CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT CHARGING SYSTEM AND BATTERY for 2AR-FE: Click here
    INSPECT CHARGING SYSTEM AND BATTERY for A25A-FKS: Click here
    INSPECT CHARGING SYSTEM AND BATTERY for 2GR-FKS: Click here

    OK

  3. CHECK CONNECTOR


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.

    5. Check that the terminals of the connector are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  4. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    1. B006ZWOC01
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K73-36 (IG2) - Body ground Ignition switch ON 8 to 16 V

    5. Turn the ignition switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K73-33 (E1) - Body ground Always Below 1 Ω
      K73-32 (E2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  5. CHECK SRS WARNING LIGHT


    1. Turn the ignition switch to ON and check the SRS warning light condition.

      OK
      After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.

      Tech Tips

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

  6. CHECK CAN COMMUNICATION SYSTEM


    1. Using the GTS, check if the CAN communication system is functioning normally.

      OK
      CAN communication system is functioning normally.

      Tech Tips

      Refer to Communication Bus Check in CAN Communication System.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    GO TO CAN COMMUNICATION SYSTEM Click here

    OK

  7. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    INSPECT CHARGING SYSTEM AND BATTERY for 2AR-FE: Click here
    INSPECT CHARGING SYSTEM AND BATTERY for A25A-FKS: Click here
    INSPECT CHARGING SYSTEM AND BATTERY for 2GR-FKS: Click here

    OK

  8. CHECK CONNECTOR


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the airbag sensor assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the airbag sensor assembly.

    5. Check that the terminals of the connector are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  9. CHECK WIRE HARNESS (AIRBAG SENSOR ASSEMBLY - BODY GROUND)


    1. B006ZWOC01
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Operate all components of the electrical systems (defogger, wipers, headlights, heater blower, etc.).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K73-36 (IG2) - Body ground Ignition switch ON 8 to 16 V

    5. Turn the ignition switch off.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K73-33 (E1) - Body ground Always Below 1 Ω
      K73-32 (E2) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE WIRE HARNESS

    OK

  10. CHECK CONNECTOR


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Check that the connector is properly connected to the combination meter assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not properly connected, reconnect the connector and proceed to the next inspection.

    3. Disconnect the connector from the combination meter assembly.

    4. Check that the terminals of the connector are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE CONNECTOR

    OK

  11. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)


    1. B00719FC47
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      K21-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
      K21-40 (B) - Body ground Always 11 to 14 V

    4. Turn the ignition switch off.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      K21-21 (ES) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE WIRE HARNESS

    OK

  12. CHECK SRS WARNING LIGHT


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Connect the connector to the combination meter assembly.

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON and check the SRS warning light condition.

      OK
      After the primary check period, the SRS warning light turns off for approximately 10 seconds and then turns back on.

      Tech Tips

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    NG

    REPLACE COMBINATION METER ASSEMBLY Click here