AIRBAG SYSTEM, Diagnostic DTC:B1925, B1926, B1927, B1928

DTC Code DTC Name
B1925 Short in Rear P/T Squib (LH) Circuit
B1926 Open in Rear P/T Squib (LH) Circuit
B1927 Short in Rear P/T Squib (LH) Circuit (to Ground)
B1928 Short in Rear P/T Squib (LH) Circuit (to +B)

DESCRIPTION

The rear pretensioner squib LH circuit consists of the airbag sensor assembly and rear seat outer belt assembly LH.

The airbag sensor assembly uses this circuit to deploy the pretensioner when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the rear pretensioner squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Test Mode / Check Mode
B1925 Short in Rear P/T Squib (LH) Circuit

  • The airbag sensor assembly detects a line short in the rear pretensioner squib LH circuit during the primary check.

  • Rear pretensioner squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Rear pretensioner squib LH (Rear seat outer belt assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1926 Open in Rear P/T Squib (LH) Circuit

  • The airbag sensor assembly detects an open in the rear pretensioner squib LH circuit.

  • Rear pretensioner squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Rear pretensioner squib LH (Rear seat outer belt assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1927 Short in Rear P/T Squib (LH) Circuit (to Ground)

  • The airbag sensor assembly detects a short to ground in the rear pretensioner squib LH circuit.

  • Rear pretensioner squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Rear pretensioner squib LH (Rear seat outer belt assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode
B1928 Short in Rear P/T Squib (LH) Circuit (to +B)

  • The airbag sensor assembly detects a short to B+ in the rear pretensioner squib LH circuit.

  • Rear pretensioner squib LH malfunction

  • Airbag sensor assembly malfunction

  • Floor wire

  • Rear pretensioner squib LH (Rear seat outer belt assembly LH)

  • Airbag sensor assembly

 Comes on Applies to check mode

WIRING DIAGRAM

B0070XPE46
*a Rear Pretensioner Squib LH (Rear Seat Outer Belt Assembly LH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

Tech Tips


  • Perform the simulation method by selecting check mode (Signal Check) using the GTS.

    Click here

  • After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road.

    Click here

PROCEDURE


  1. CHECK CONNECTORS


    1. B0070WMC01
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the rear seat outer belt assembly LH and airbag sensor assembly.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the rear seat outer belt assembly LH and airbag sensor assembly.

    5. Check that the terminals of the connectors are not deformed or damaged.

      OK
      The terminals are not deformed or damaged.

    6. Check that the floor wire connector (on the rear seat outer belt assembly LH side) is not loose, deformed or damaged.

      OK
      The airbag connector locking button is not disengaged, and the claw of the lock is not deformed or damaged.

    7. Check that the short springs of the activation prevention mechanism of the floor wire connector are not deformed or damaged.

      OK
      The short springs are not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  2. CHECK REAR SEAT OUTER BELT ASSEMBLY LH


    1. B0071V8C29
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *a

      Front view of wire harness connector

      (to Rear Seat Outer Belt Assembly LH)

      Connect the connector to the airbag sensor assembly.

    2. Connect SST (resistance 2.1 Ω) to connector C.

      CAUTION:

      Never connect a tester to the rear seat outer belt assembly LH for measurement, as this may lead to a serious injury due to pretensioner deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting it.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    3. Connect the cable to the negative (-) battery terminal.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 60 seconds.

    8. Check for DTCs.


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1925, B1926, B1927 or B1928 is not output.

      Tech Tips

      Codes other than DTCs B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    11. Disconnect SST from connector C.

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE REAR SEAT OUTER BELT ASSEMBLY LH Click here

    NG

  3. CHECK FLOOR WIRE


    1. B007184C27
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly
      *3 Floor Wire
      *a

      Front view of wire harness connector

      (to Rear Seat Outer Belt Assembly LH)

      Disconnect the floor wire from the airbag sensor assembly.

    2. Check for a short to B+ in the circuit.


      1. Connect the cable to the negative (-) battery terminal.

      2. Turn the ignition switch to ON.

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R55-1 (RL+) - Body ground Ignition switch ON Below 1 V
        R55-2 (RL-) - Body ground Ignition switch ON Below 1 V

      4. Turn the ignition switch off.

      5. Disconnect the cable from the negative (-) battery terminal.

        CAUTION:

        Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check for an open in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R55-1 (RL+) - R55-2 (RL-) Always Below 1 Ω

    4. Check for a short to ground in the circuit.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R55-1 (RL+) - Body ground Always 1 MΩ or higher
        R55-2 (RL-) - Body ground Always 1 MΩ or higher

    5. Check for a short in the circuit.


      1. Release the activation prevention mechanism built into connector B.

        Click here

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R55-1 (RL+) - R55-2 (RL-) Always 1 MΩ or higher

      3. Restore the released activation prevention mechanism of connector B to the original condition.

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK DTC


    1. B006Z1ZC17
      *1 Rear Seat Outer Belt Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the rear seat outer belt assembly LH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.


      Body Electrical > SRS Airbag > Trouble Codes
      OK
      DTC B1925, B1926, B1927 or B1928 is not output.

      Tech Tips

      Codes other than DTCs B1925, B1926, B1927 and B1928 may be output at this time, but they are not related to this check.

      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here