REAR DOOR COURTESY SWITCH REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door courtesy light switch assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

B0071E9

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION (w/ Rear Seat Side Airbag)

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Rear Seat Side Airbag)

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If an airbag deploys for any reason, it may cause a serious injury.

    B006XLM

  3. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fixed Seat Type)

    Click here

  4. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)

    Click here

  5. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fixed Seat Type)

    Click here

  6. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)

    Click here

  7. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Fold Down Seat Type)

    Click here

  8. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fold Down Seat Type)

    Click here

  9. REMOVE REAR SEAT CUSHION LOCK HOOK (for Fold Down Seat Type)

    Click here

  10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP (for Fold Down Seat Type)

    Click here

  11. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Fold Down Seat Type)

    Click here

  12. REMOVE REAR SEAT HEADREST ASSEMBLY (for Reclining Seat Type)

    Click here

  13. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY (for Reclining Seat Type)

    Click here

  14. REMOVE REAR SEAT CUSHION ASSEMBLY (for Reclining Seat Type)

    Click here

  15. REMOVE REAR SEAT CUSHION LOCK HOOK (for Reclining Seat Type)

    Click here

  16. REMOVE REAR SEATBACK COVER (for Reclining Seat Type)

    Click here

  17. REMOVE REAR SEATBACK ASSEMBLY (for Reclining Seat Type)

    Click here

  18. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP (for Reclining Seat Type)

    Click here

  19. REMOVE REAR SIDE SEATBACK ASSEMBLY (for Reclining Seat Type)

    Click here

  20. REMOVE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY


    1. B0070PT

      Using a T30 "TORX" socket wrench, remove the screw.

    2. Disconnect the connector to remove the rear door courtesy light switch assembly.