IMMOBILISER SYSTEM(w/o Smart Entry and Start System) DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Immobiliser / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Immobiliser > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Key SW Unlock warning switch signal ON or OFF

      ON: Door control transmitter assembly in ignition key cylinder

      OFF: No door control transmitter assembly in ignition key cylinder

      		 -
      IG SW Ignition switch signal ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch ACC or off

      		 -
      Immobiliser Immobiliser system status Set or Unset

      Set: No door control transmitter assembly in ignition key cylinder, or 20 sec. elapsed after turning the ignition switch to ACC or off

      Unset: Door control transmitter assembly in ignition key cylinder

      		 -
      Response Transponder chip data NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Frame Error Transponder chip data NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Different Serial Number Transponder chip data NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Different Encrypt Code Transponder chip data NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Abnormal Status Transponder chip data NG or OK

      NG: Data error

      OK: Data OK

      		 -
      Bcc Malfunction Transponder chip data NG or OK

      NG: Incorrect data being sent

      OK: Correct data being sent

      		 -
      Sub Key Sub key ID code signal Reg or Unreg

      Reg: Registered sub key ID code sent

      Unreg: Unmatching sub key ID code sent

      		 -
      Master Key Master key ID code signal Reg or Unreg

      Reg: Registered master key ID code sent

      Unreg: Unmatching master key ID code sent

      		 -
      Transponder S-code Number of registered sub key min. 0, max. 15 Number of registered sub keys displayed -
      Transponder M-code Number of registered master key min. 0, max. 15 Number of registered master keys displayed -
      +B Power source Break or Normal

      Break: Power source open

      Normal: Power source normal

      		 -
      Antenna Coil Status Transponder key coil condition Normal or Fail

      Normal: Antenna coil normal

      Fail: Antenna coil malfunctioning

      		 -
      E/G Start Permission Engine start permission NG or OK

      NG: Engine start not permitted

      OK: Engine start permitted

      		 -
      The Number of DTCs Number of DTCs Min.: 0, Max.: 255 Number of stored DTCs -

      Tech Tips

      Data from an actual vehicle provided for reference.

      B0070SVE06

      • *1: Insert a door control transmitter assembly into the ignition key cylinder and turn the ignition switch to ACC.

      • *2: Turn the ignition switch to ON.

      • *3: Turn the ignition switch off and remove the door control transmitter assembly from the ignition key cylinder.

  2. ACTIVE TEST

    Tech Tips

    Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body or Immobiliser / Active Test.

    5. Perform the Active Test according to the display on the GTS.


      Body Electrical > Main Body > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Security Indicator Security indicator light (telltale light assembly) OFF/ON -

      Body Electrical > Immobiliser > Active Test
      Tester Display Measurement Item Control Range Diagnostic Note
      Security Indicator Security indicator light (telltale light assembly) OFF/ON -