REAR DOOR LOCK INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B004HGDC01
      B006ZFL Install in this Direction

      Install the rear door inside locking cable assembly as shown in the illustration.

  2. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B004JOKC01
      B006ZFL Install in this Direction

      Install the rear door lock remote control cable assembly as shown in the illustration.

  3. INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY


    1. B004N6QC01
      B006ZFL Install in this Direction

      Engage the 2 claws as shown in the illustration.

    2. B004JMU

      Engage the 2 claws to install the rear door lock cover sub-assembly as shown in the illustration.

  4. INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

    Note


    • When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.

    • Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.

    • Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.


    1. Apply MP grease to the sliding parts of the rear door lock with motor assembly.

    2. When reusing the rear door lock with motor assembly:


      1. Install a new door lock wiring harness seal to the rear door lock with motor assembly.

    3. B004I50C01
      *a Release Plate
      B006ZFL Install in this Direction

      Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.

      Tech Tips

      Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.

    4. Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  5. INSTALL REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  6. INSTALL REAR DOOR QUARTER WINDOW GLASS

    Click here

  7. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

    Click here

  8. CONNECT REAR DOOR WEATHERSTRIP


    1. Connect the rear door weatherstrip.

  9. INSTALL REAR DOOR GLASS RUN

    Click here

  10. INSTALL REAR DOOR PANEL PROTECTOR

    Click here

  11. INSTALL REAR DOOR NO. 1 VENT SEAL

    Click here

  12. INSTALL REAR DOOR SERVICE HOLE COVER

    Click here

  13. INSTALL REAR DOOR NO. 2 SERVICE HOLE COVER

    Click here

  14. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

  15. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  16. INSTALL REAR ARMREST ASSEMBLY

    Click here

  17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

    Click here

  18. INSTALL REAR DOOR ARMREST COVER SUB-ASSEMBLY

    Click here

  19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

  20. INITIALIZE POWER WINDOW CONTROL SYSTEM

    Click here

  21. INSPECT POWER WINDOW OPERATION

    Click here