REAR DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here


  • Rear door glass sub-assembly

  • Rear door glass run

 Initialize power window control system

  • Auto up and down function

  • Jam protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Catch protection function

  • Window open warning function

Click here

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    for 2AR-FE:

    Click here

    for A25A-FKS:

    Click here

    for 2GR-FKS:

    Click here

  3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

    Click here

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

    Click here

  5. REMOVE REAR ARMREST ASSEMBLY

    Click here

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

    Click here

  8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

    Click here

  9. REMOVE REAR DOOR SERVICE HOLE COVER

    Click here

  10. REMOVE REAR DOOR NO. 1 VENT SEAL

    Click here

  11. REMOVE REAR DOOR PANEL PROTECTOR

    Click here

  12. REMOVE REAR DOOR GLASS RUN

    Click here

  13. DISCONNECT REAR DOOR WEATHERSTRIP


    1. Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.

  14. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

    Click here

  15. REMOVE REAR DOOR QUARTER WINDOW GLASS

    Click here

  16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

    Click here

  17. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    1. B00705VC01
      *a Release Plate
      B006ZFL Remove in this Direction

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

    3. When reusing the rear door lock with motor assembly:


      1. B006YDA

        Remove the door lock wiring harness seal from the rear door lock with motor assembly.

  18. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY


    1. B0071VA

      Using a screwdriver, disengage the 2 claws as shown in the illustration.

    2. B006ZXZC01
      B006ZFL Remove in this Direction

      Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.

  19. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. B006Z5KC01
      B006ZFL Remove in this Direction

      Remove the rear door lock remote control cable assembly as shown in the illustration.

  20. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. B006YQXC01
      B006ZFL Remove in this Direction

      Remove the rear door inside locking cable assembly as shown in the illustration.