FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)	Click here
	Perform steering sensor zero point calibration	Pre-collision system	Click here
	Memorize steering angle neutral point	Parking assist monitor system	Click here
Front door glass sub-assembly Front door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function	Click here

Tech Tips

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

PRECAUTION

Note

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for 2AR-FE:

Click here

for A25A-FKS:

Click here

for 2GR-FKS:

Click here
REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here
REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here
REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here
REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here
REMOVE FRONT ARMREST ASSEMBLY

Click here
REMOVE COURTESY LIGHT ASSEMBLY

Click here
REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here
REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here
REMOVE FRONT DOOR SERVICE HOLE COVER

Click here
REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here
REMOVE FRONT DOOR PANEL PROTECTOR

Click here
REMOVE FRONT DOOR GLASS RUN

Click here
REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

Click here
REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (for Driver Side)

Click here
REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY (for Driver Side)

Click here
REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY
1. *1 Front Door Lock Open Rod
  
  Remove in this Direction
  
  Disconnect the connector.
2. Using a T30 "TORX" socket wrench, remove the 3 screws.
3. Slide the front door lock with motor assembly downward to disconnect the front door lock open rod and remove the front door lock with motor assembly and cables as a unit.
4. When reusing the front door lock with motor assembly:
  1. Remove the door lock wiring harness seal from the front door lock with motor assembly.
REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY
1. Using a screwdriver, disengage the 2 claws as shown in the illustration.
2. Remove in this Direction
  
  Disengage the 2 claws to remove the front door lock cover sub-assembly as shown in the illustration.
REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
1. Remove in this Direction
  
  Remove the front door lock remote control cable assembly as shown in the illustration.
REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
1. Remove in this Direction
  
  Remove the front door inside locking cable assembly as shown in the illustration.

*1	Front Door Lock Open Rod
	Remove in this Direction