WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Smart Entry and Start System) PRECAUTION

PRECAUTION FOR DISCONNECTING CABLE FROM NEGATIVE BATTERY TERMINAL

PRECAUTIONS WHEN USING GTS

1. When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Smart Key(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

DOOR CONTROL RECEIVER EXPRESSIONS

1. The type of door control receiver used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

   Vehicle Specification	Part Name in Manual	Actual Part Name
   for 12 Pin Type	Door control receiver	Electrical key and tire pressure monitoring system receiver assembly
   for 5 Pin Type	Door control receiver	Smart door control receiver assembly

PRECAUTION FOR REGISTRATION

1. Before replacing any of the following parts, refer to Service Bulletin.

   
   

   • Certification ECU (smart key ECU assembly)

   • Electrical key transmitter sub-assembly

   • Main body ECU (multiplex network body ECU)

2. Electrical key and tire pressure monitoring system receiver assembly

   
   

   1. When replacing the electrical key and tire pressure monitoring system receiver assembly, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

      Click here

   2. If the electrical key and tire pressure monitoring system receiver assembly has been replaced, it is necessary to perform initialization (Click here ) after registration Click here of the transmitter IDs to the electrical key and tire pressure monitoring system receiver assembly.

PRECAUTIONS FOR ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY

Click here

NOTICE WHEN CHECKING FOLLOWING

1. Wireless door lock/unlock function:

   This wireless door lock control function operates only when the following 3 conditions are met:

   
   

   1. The engine switch is off.

   2. All of the doors are closed.

   3. The power door lock control system is operating properly.

      Tech Tips

      The unlock function operates even when a door is open.

2. The size of the wireless door lock control operation area differs depending on the situation.

   
   

   1. The size of the operation area differs depending on the user and the way the electrical key transmitter sub-assembly is held.

   2. In certain areas, the wireless door lock control function will only operate partially for the operation area, which will be reduced due to the vehicle body shape and the influence of the surrounding environment.

   3. Since the electrical key transmitter sub-assembly uses weak radio waves, strong radio waves or electrical noise in the frequency used by the electrical key transmitter sub-assembly may reduce the size of the operation area and the remote control may not function.

   4. When the transmitter battery is weak, the size of the operation area is reduced and the remote control may not function.

      Tech Tips

      
      

      • If the electrical key transmitter sub-assembly has been left in a place that is exposed to direct sunlight, such as on the instrument panel, it may cause the battery to be weakened or cause other related problems.

      • Do not place the electrical key transmitter sub-assembly near magnetic equipment, such as digital audio players, induction cookers, medical devices that generate low-frequency electromagnetic waves, etc.

3. Multi channel function

   The wireless door lock control system has a multi channel function. Each time the switch on the electrical key transmitter sub-assembly is pressed, the channel is switched alternately between 2 different frequencies and the signal is sent to the door control receiver.

PRECAUTIONS FOR INSPECTING POWER SOURCE FOR MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (w/ Door Control Battery)

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. If a main body ECU (multiplex network body ECU) power source malfunction occurs, the door control battery may be malfunctioning.