BLIND SPOT MONITOR SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Blind Spot Monitor Master or Blind Spot Monitor Slave / Data List.

    5. Read the Data List according to the display on the GTS.


      Body Electrical > Blind Spot Monitor Master > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Main Switch State of the Blind spot monitor system OFF or ON

      OFF: Blind spot monitor system off

      ON: Blind spot monitor system on

      		 -
      RCTA Switch Status State of the RCTA function OFF or ON

      OFF: RCTA function off

      ON: RCTA function on

      		 -
      Warning Indicator Turning on(Master) State of the outer rear view mirror indicator RH turning on OFF or ON

      • OFF: Any state except "ON" state

      • ON: Either of the following state


        • During initial check

        • Blind spot monitor system on, vehicle detected on left hand side and turn signal switch not operated

      		 -
      Warning Indicator Flashing(Master) State of the outer rear view mirror indicator RH flashing OFF or ON

      • OFF: Any state except "ON" state

      • ON: Either of the following state


        • Blind spot monitor system on, vehicle detected on left hand side and left side of turn signal switch on

        • Vehicle detected by RCTA function

      		 -
      Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V

      Indicator illuminated: 2.5 to 7.5 V

      Indicator not illuminated: Below 1 V

      		 -
      Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA

      Indicator illuminated: 5 to 100 mA

      Indicator not illuminated: 0 mA

      		 -
      Turn Switch State State of the turn signal switch Left ON, Right ON or OFF

      Left ON: Left turn signal switch on

      Right ON: Right turn signal switch on

      OFF: Turn signal switch off

      		 -
      Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON

      OFF: Shift lever in any position except R

      ON: Shift lever in R

      		 -
      Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering sensor Min.: -3072 deg, Max.: 3070.5 deg

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      HV Flag Hybrid vehicle OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl

      Incompl: Adjustment not completed

      Compl: Adjustment completed

      		 Changes to "Compl" when blind spot monitor beam axis adjustment has been finished
      Destination Undefined Flag Destination determination Unfixed or Fixed

      Unfixed: Sensor destination information not determined

      Fixed: Sensor destination information determined according to CAN destination information

      		 -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed -
      RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON

      OFF: w/o RCTA function

      ON: w/ RCTA function

      		 -
      Master Side RCTA Function Switches the RCTA function on and off OFF or ON

      ON: RCTA function on

      OFF: RCTA function off

      		 -
      Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
      Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% -
      Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s

      Turning right: -125 to 0 deg/s

      Turning left: 0 to 124.612 deg/s

      		 -
      BSM Mirror Indicator Brightness Brightness of the indicators in the outer rear view mirror assemblies Dark or Bright

      Dark: Outer mirror indicator brightness low

      Dark: Outer mirror indicator brightness low

      		 -
      Mounting FHL Function Existence of FHL function Without or With

      Without: w/o FHL function

      With: w/ FHL function

      		 -
      Number of DTC Number of DTC Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -

      Body Electrical > Blind Spot Monitor Slave > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator LH turning on OFF or ON

      • OFF: Any state except "ON" state

      • ON: Either of the following state


        • During initial check

        • Blind spot monitor system on, vehicle detected on right hand side and turn signal switch not operated

      		 -
      Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator LH flashing OFF or ON

      • OFF: Any state except "ON" state

      • ON: Either of the following state


        • Blind spot monitor system on, vehicle detected on right hand side and right side of turn signal switch on

        • Vehicle detected by RCTA function

      		 -
      Buzzer Sound Status State of the RCTA buzzer (blind spot monitor buzzer) OFF or ON

      OFF: Buzzer not sounding

      ON: Buzzer sounding

      		 -
      Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V

      Indicator illuminated: 2.5 to 7.5 V

      Indicator not illuminated: Below 1 V

      		 -
      Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA

      Indicator illuminated: 5 to 100 mA

      Indicator not illuminated: 0 mA

      		 -
      Buzzer Input Circuit Voltage RCTA buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V

      Buzzer not sounding: 11 to 14 V

      Buzzer sounding: Alternating between 0 to 14 V

      		 -
      Turn Switch State State of the turn signal switch Left ON, Right ON or OFF

      Left ON: Left turn signal switch on

      Right ON: Right turn signal switch on

      OFF: Turn signal switch off

      		 -
      Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON

      OFF: Shift lever in any position except R

      ON: Shift lever in R

      		 -
      Vehicle Speed Vehicle speed signal Min.: -327.68 km/h (-204 mph), Max.: 327.67 km/h (204 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering sensor Min.: -3072 deg, Max.: 3070.5 deg

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 49.951 V Engine switch on (IG): 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      HV Flag Hybrid vehicle OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Beam Axis Inspection Completeness Flag Completion of beam axis adjustment Incompl or Compl

      Incompl: Adjustment not completed

      Compl: Adjustment completed

      		 Changes to "Compl" when blind spot monitor beam axis adjustment has been finished
      Destination Undefined Flag Destination determination Unfixed or Fixed

      Unfixed: Sensor destination information not determined

      Fixed: Sensor destination information determined according to CAN destination information

      		 -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -180 deg, Max.: Over 180 deg Angle adjusted using auto alignment is displayed -
      RCTA Equipped Information State of the RCTA equipped information / OFF or ON OFF or ON

      OFF: w/o RCTA function

      ON: w/ RCTA function

      		 -
      Slave Side RCTA Function Switches the RCTA function on and off OFF or ON

      OFF: RCTA function off

      ON: RCTA function on

      		 -
      Mirror LED Control Frequency Frequency of the outer rear view mirror indicator on the outer mirror when blinking Min.: 1500 Hz, Max.: 2400 Hz Always: 2000 Hz -
      Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50% -
      Buzzer Control Frequency Frequency of RCTA buzzer (blind spot monitor buzzer) when sounding Min.: 1000 Hz, Max.: 2400 Hz Always: 2000 Hz -
      Yaw Rate Sensor Yaw rate sensor Min.: Under -125 deg/s, Max.: 124.612 deg/s

      Turning right: -125 to 0 deg/s

      Turning left: 0 to 124.612 deg/s

      		 -
      BSM Buzzer Volume Adjust Volume of the RCTA buzzer (blind spot monitor buzzer) Low, Medium or High

      Low: Buzzer volume less than that of medium

      Medium: Default buzzer volume

      High: Buzzer volume more than that of medium

      		 -
      Mounting FHL Function Existence of FHL function Without or With

      Without: w/o FHL function

      With: w/ FHL function

      		 -
      Number of DTC Number of DTC Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -