RADIO ANTENNA CORD INSTALLATION

PROCEDURE


  1. INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ Digital Audio Broadcasting Antenna)


    1. Engage the 9 clamps to install the No. 4 antenna cord sub-assembly.

    2. Connect the connector.

  2. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Tech Tips

    Butyl tape and adhesive tape are not available as supply parts. If these pieces of tape still have enough adhesion to secure the No. 2 antenna cord sub-assembly to the roof headlining assembly, reuse them. If the adhesive tape and/or the butyl tape is no longer sticky, apply new tape following the procedure below.


    1. Apply new butyl tape.

      for Normal Roof:

      B006Z02C01
      *A w/o Television Antenna *B w/ Television Antenna
      *a Marking - -
      B0071FR Butyl tape - -

      for Moon Roof:

      B006YOTC02
      *a Marking - -
      B0071FR Butyl tape - -

      for Panoramic Moon Roof:

      B006XWYC01
      *A w/o Television Antenna *B w/ Television Antenna
      *a Marking - -
      B0071FR Butyl tape - -

      1. Remove the old butyl tape from the roof headlining assembly.

      2. Prepare an appropriate amount of new butyl tape.

        Tech Tips

        Be careful not to touch the adhesive surface.

      3. Apply the butyl tape to the roof headlining assembly while aligning the tape with the markings on the roof headlining assembly.

      4. Peel off the release paper from the butyl tape.

    2. w/o Television Antenna:


      1. Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

        for Normal Roof:

        B0071T1C02
        *a Marking Tape (A) *b Marking Tape (B)
        *c Marking Tape (C) *d Protrusion
        B006Y8C Adhesive Tape B006XFD Adjustment Area

        for Moon Roof:

        B006X1YC02
        *a Marking Tape (A) *b Marking Tape (B)
        *c Marking Tape (C) *d Protrusion
        B006Y8C Adhesive Tape B006XFD Adjustment Area

        for Panoramic Moon Roof:

        B00715SC04
        *a Marking Tape (A) *b Marking Tape (B)
        *c Marking Tape (C) *d Protrusion
        B006Y8C Adhesive Tape B006XFD Adjustment Area

      2. Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

      3. Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

      4. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly.

        Note


        • Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

        • Make sure the No. 2 antenna cord sub-assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.

        Tech Tips

        Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.

      5. Apply the adhesive tape as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

    3. w/ Television Antenna:


      1. Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

        B006YMHC02
        *A for Normal Roof *B for Panoramic Moon Roof
        *a Marking Tape (A) *b Marking Tape (B)
        *c Marking Tape (C) *d Marking Tape (D)
        *e Protrusion *f Marking
        B006Y8C Adhesive Tape B006XFD Adjustment Area

      2. Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

      3. Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining assembly and wrap tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining assembly.

      4. Align the marking tape (D) on the No. 2 antenna cord sub-assembly with the marking on the roof headlining assembly and secure the No. 2 antenna cord sub-assembly with the adhesive tape as shown in the illustration.

      5. Install the No. 2 antenna cord sub-assembly to the roof headlining assembly.

        Note


        • Make sure that there are no gaps between the roof headlining assembly and No. 2 antenna cord sub-assembly, and that the No. 2 antenna cord sub-assembly is not twisted.

        • Make sure the No. 2 antenna cord sub-assembly is securely installed. If any part of the No. 2 antenna cord sub-assembly is loose, it will cause an abnormal noise.

        Tech Tips

        Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area.

      6. Apply the adhesive tape as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

  3. INSTALL ROOF HEADLINING ASSEMBLY

    Click here

  4. INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)


    1. Engage the 6 clamps to install the antenna cord sub-assembly.

  5. INSTALL NO. 3 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for LHD)

    Click here

  6. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT (for LHD)

    Click here

  7. INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)


    1. Engage the 6 clamps to install the antenna cord sub-assembly.

  8. INSTALL NO. 1 HEATER TO REGISTER DUCT SUB-ASSEMBLY (for RHD)

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  9. INSTALL METER MIRROR SUB-ASSEMBLY (for RHD)

    w/ Headup Display:

    Click here

  10. INSTALL DEFROSTER NOZZLE ASSEMBLY (for RHD)

    w/ Headup Display:

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  11. INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT (for RHD)

    w/ Headup Display:

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  12. INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT (for RHD)

    Tech Tips

    Use the same procedure as for LHD.

    Click here

  13. INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

    Click here