STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) INSTALLATION

PROCEDURE


  1. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  2. INSTALL STEERING COLUMN ASSEMBLY

    Note

    Make sure that the wire harness is not interfering with the steering column assembly.


    1. Install the steering column assembly with the bolt and 2 nuts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

      Note


      • After the column is installed, check the tilt operation.

      • If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

        Tighten the nuts and check the tilt operation again.

    2. Connect each connector and engage each wire harness clamp to the steering column assembly.

  3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. B006Z79C01
      *a Matchmark

      Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.

    2. Install the steering intermediate shaft assembly to the steering column assembly.

    3. Install the bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    4. B006ZXK

      Tighten the clamp.

  4. INSTALL STEERING COLUMN HOLE COVER


    1. B0070KQ

      Install the steering column hole cover with the 2 clips.

    2. Install the clip.

    3. Return the floor carpet.

  5. CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  6. INSTALL FRONT WHEEL LH (for LHD)

    Click here

  7. INSTALL FRONT WHEEL RH (for RHD)

    Click here

  8. INSTALL NO. 1 AIR DUCT (for LHD)


    1. B006ZWP

      Engage the 3 claws to install a new No. 1 air duct.

    2. Install the 2 bolts.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  9. INSTALL NO. 1 AIR DUCT (for RHD)


    1. B0071UW

      Engage the 3 claws to install a new No. 1 air duct.

    2. Install the 2 bolts.

      Torque:
      9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

  10. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  11. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. B00714NC01
      *a Clamp

      Using pliers, expand the clamp.

    2. While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.

    3. Return the clamp to its original position.

    4. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

  12. INSTALL TRANSPONDER KEY COIL (w/o Smart Key System)


    1. B007111

      Engage the 2 claws to install the transponder key coil.

    2. Connect the connector.

  13. INSTALL UPPER STEERING COLUMN COVER


    1. B006ZPJ

      Engage the 2 claws and 4 clips to connect the upper steering column cover.

    2. B006YIBC01
      B006ZFL Install in this direction

      Engage the claw to install the upper steering column cover.

  14. INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY


    1. B006X12

      Engage the 2 claws to install the lower steering column cover sub-assembly.

    2. B006YI7

      Install the 3 screws.

  15. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  16. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Click here

  17. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  18. CHECK STEERING WHEEL CENTER POINT

  19. INSTALL HORN BUTTON ASSEMBLY

    Click here

  20. PERFORM INITIALIZATION AND CALIBRATION (w/ Parking Assist Monitor System)

    for Initialization: Click here

    for Calibration: Click here