STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

Steering sensor

  • Steering angle neutral point (Initialize parking assist monitor system)

  • Steering angle setting

 Parking assist monitor system

for Initialization: Click here

for Calibration: Click here

Steering lock ECU (steering lock actuator or upper bracket assembly)*1 Perform code registration (Immobiliser function) Smart Entry and Start System (for Start Function) See Service Bulletin for the registration method.
*1: w/ Smart Entry and Start System

PROCEDURE


  1. PRECAUTION

    Click here

  2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

  3. REMOVE HORN BUTTON ASSEMBLY

    Click here

  4. REMOVE STEERING WHEEL ASSEMBLY

    Click here

  5. REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

    Note

    Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.


    1. Release the tilt and telescopic lever and fully extend and lower the steering column assembly.

    2. Lock the tilt and telescopic lever.

    3. B006YI7

      Remove the 3 screws.

    4. B006YHXC01
      B006Y8C Push Area
      B006ZFL Push in this Direction

      While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.

  6. REMOVE UPPER STEERING COLUMN COVER


    1. B006XNIC01
      B006ZFL Separate in this direction

      Disengage the claw and separate the upper steering column cover.

    2. B006ZPJ

      Disengage the 2 claws and 4 clips to remove the upper steering column cover.

  7. REMOVE TRANSPONDER KEY COIL (w/o Smart Key System)


    1. B007111

      Disconnect the connector.

    2. Disengage the 2 claws and remove the transponder key coil.

  8. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

    • Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

    • Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.


    1. Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.

    2. B006YC0C01
      *a Clamp

      Using pliers, expand the clamp.

    3. While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.

  9. REMOVE FRONT DOOR SCUFF PLATE

    Click here

  10. REMOVE COWL SIDE TRIM SUB-ASSEMBLY

    Click here

  11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP


    1. Disconnect the front door opening trim weatherstrip.

      Tech Tips

      Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.

  12. REMOVE INSTRUMENT SIDE PANEL

    Click here

  13. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    for LHD: Click here

    for RHD: Click here

  14. REMOVE NO. 2 METER HOOD CLUSTER

    Click here

  15. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

    Click here

  16. REMOVE NO. 1 METER HOOD CLUSTER

    Click here

  17. REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

    Click here

  18. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

    w/ Driver Side Knee Airbag: Click here

    w/o Driver Side Knee Airbag: Click here

  19. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

    for LHD: Click here

    for RHD: Click here

  20. REMOVE NO. 1 AIR DUCT (for LHD)


    1. B006X8VC01
      *a View A
      B006YM5 Front

      Remove the 2 bolts.

    2. Disengage the 3 claws to remove the No. 1 air duct.

      Note

      Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.

  21. REMOVE NO. 1 AIR DUCT (for RHD)


    1. B0071CVC02
      *a View A
      B006YM5 Front

      Remove the 2 bolts.

    2. Disengage the 3 claws to remove the No. 1 air duct.

      Note

      Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.

  22. REMOVE FRONT WHEEL LH (for LHD)

    Click here

  23. REMOVE FRONT WHEEL RH (for RHD)

    Click here

  24. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

    Click here

  25. REMOVE STEERING COLUMN HOLE COVER


    1. Turn back the floor carpet.

    2. B0070KQ

      Remove the clip.

    3. Disengage the 2 clips to remove the steering column hole cover.

  26. REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY


    1. B006Y55

      Using a screwdriver, loosen the clamp as shown in the illustration.

    2. B006ZYDC01
      *a Matchmark

      Remove the bolt and slide the steering intermediate shaft assembly.

      Note

      Do not remove the steering intermediate shaft assembly from the steering column assembly.

    3. Put matchmarks on the steering intermediate shaft assembly and steering column assembly.

    4. Remove the steering intermediate shaft assembly from the steering column assembly.

  27. REMOVE STEERING COLUMN ASSEMBLY


    1. Disconnect each connector and disengage each wire harness clamp from the steering column assembly.

    2. B006ZPN

      Remove the bolt, 2 nuts and steering column assembly.