FREEZE FRAME DATA
Whenever an ABS DTC is detected, the skid control ECU (brake actuator assembly) stores the current vehicle (ECU or sensor) state as Freeze Frame Data.
The skid control ECU (brake actuator assembly) stores the number of times (maximum: 31) the ignition switch has been turned from off to ON since the last time the ABS was activated.
Tech Tips
If the vehicle is stopped or driven at a low speed (7 km/h (4.3 mph) or less), or if a DTC is detected, the skid control ECU (brake actuator assembly) will stop counting the number.
Freeze Frame Data at the time the ABS operates:
The skid control ECU (brake actuator assembly) stores and updates data whenever the ABS operates.
When the ECU stores data at the time a DTC is detected, the data stored during ABS operation is cleared.
Freeze Frame Data at the time a DTC is detected:
When the skid control ECU (brake actuator assembly) stores data at the time a DTC is detected, no updates will be performed until the data is cleared.
CHECK FREEZE FRAME DATA
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.
Select a DTC to display its Freeze Frame Data.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Elapsed Time after Freeze Trigger | Elapsed time after freeze trigger | Min.: 0 msec, Max.: 510 msec | - | - |
| Number of IG ON | Number of times ignition switch turned to ON after Freeze Frame Data stored | 0 to 31 | - | - |
| Stop Light SW | Stop light switch assembly | ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Parking Brake SW | Parking brake switch assembly | ON or OFF | ON: Parking brake applied OFF: Parking brake released |
- |
| Gear Position | Gear position information | P/N, R, 1st-10th, Fail or Not R | Actual gear position | - |
| Shift Lever Position | Shift lever position information | P/N, R, D/M, 1st-6th/B or Fail | Actual shift lever position | - |
| Operated System | Operated system status | Non, ABS, VSC, TRC, BA, HAB, Fail, PBA, PB, HA-CTRL, TSC, SCB, Sys | Actual operated system | Non: No operation is activated. ABS: ABS is activated. VSC: VSC is activated. TRC: TRC is activated. BA: BA is activated. HAB: HAB is activated. Fail: Fail-safe mode is activated. PBA: PBA is activated. PB: PB is activated. HA-CTRL: Hill-start assist control is activated. TSC: Trailer sway control activated* SCB: Secondary collision brake is activated. Sys: System prohibit is activated. Tech Tips *: Not supported |
| Master Cylinder Sensor | Master cylinder pressure sensor reading | Min.: 0.00 V, Max.: 5.00 V | Brake pedal released: 0.20 to 0.40 V | Reading increases when brake pedal is depressed |
| M/C Sensor Grade | Master cylinder pressure sensor change | Min.: -30 MPa/s, Max.: 225 MPa/s | Brake pedal released or pedal held at constant position: 0 MPa/s | When brake pedal is being operated: Changes in proportion with the pedal movement speed |
| Yaw Rate Sensor | Yaw rate sensor | Min.: -128°/s, Max.: 127°/s | Vehicle stopped: 0°/s Turning right: -128 to 0°/s Turning left: 0 to 127°/s |
- |
| Lateral G | Lateral G | Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
- | During turning: Changes in proportion with lateral acceleration |
| Forward and Rearward G | Forward and backward G | Min.: - 25.10 m/s2, Max.: 24.90 m/s2 |
- | During acceleration/deceleration: Changes in proportion with acceleration |
| FR Wheel Speed | Front wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| FL Wheel Speed | Front wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RR Wheel Speed | Rear wheel speed sensor RH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| RL Wheel Speed | Rear wheel speed sensor LH reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph), Max.: 326.4 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | When driving at constant speed: No large fluctuations |
| Vehicle Speed Grade | Vehicle speed grade | Min.: -25.10 m/s2, Max.: 24.90 m/s2 |
Vehicle stopped: 0 m/s2 |
During driving: Changes in proportion with vehicle acceleration/deceleration |
| Real Engine Torque | Actual engine torque | Min.: -1024 Nm, Max.: 1023 Nm | - | - |
| Accelerator Opening Angle % | Percentage of accelerator pedal opening angle | Min.: 0.0%, Max.: 127.5% | The accelerator pedal released: 0.0% | During accelerator pedal operation: Changes in proportion with the pedal movement |
| Inspection Mode | Inspection mode | Other or Inspect | Other: Normal mode Inspect: Inspection mode |
- |
| Steering Angle Sensor | Steering angle sensor | Min.: - 3276.8°, Max.: 3276.7° | Left turn: Increase Right turn: Decrease |
- |
| TRC/VSC Off Mode | TRC/VSC off mode | Normal, TRC OFF, VSC Expert Mode, VSC OFF | Normal: Normal mode TRC OFF: TRC off mode VSC Expert Mode: VSC expert mode VSC OFF: VSC off mode |
- |
| Brake Hold Ready | Brake hold control permission status | OFF or ON | ON: Brake hold control permitted OFF: Brake hold control not permitted |
- |
| Brake Hold Control Mode | Brake hold control mode | OFF, ON, Release or EPB | OFF: Brake hold control is not operating ON: Brake hold control is operating Release: Brake hold control is released EPB: Parking brake is engaged during brake hold control |
Tech Tips EPB stands for electric parking brake. |
CLEAR FREEZE FRAME DATA
Note
Clearing the DTCs will also clear the Freeze Frame Data.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs and Freeze Frame Data.