REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)


    1. B006ZJFC02
      *A Type A
      *B Type B
      *a View from Underneath
      B006Z38 Front of the Vehicle
      B006ZY0 Outside of the Vehicle

      Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

      Note


      • Position the rear suspension member front body mounting cushion in the correct direction.

      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.

    2. B006WX0N01

      Install SST as shown in the illustration.

      SST
      09570-24011
      09830-10010   ( 09830-01010, 09830-01020, 09830-01040, 09830-01050 )

      Note

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

    3. B0070SMC03
      *a Hold
      B006ZFL Turn

      Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

      SST
      09570-24011
      09830-10010   ( 09830-01010, 09830-01020, 09830-01040, 09830-01050 )

      Note

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

    4. Remove SST from the rear suspension member sub-assembly.

  2. INSTALL REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)


    1. B007160C02
      *A Type A
      *B Type B
      *a View from Underneath
      B006Z38 Front of the Vehicle
      B006ZY0 Outside of the Vehicle

      Confirm the installation direction and temporarily install a new rear suspension member front body mounting cushion.

      Note


      • Position the rear suspension member front body mounting cushion in the correct direction.

      • Do not apply lubricant to the outer sleeve of the rear suspension member front body mounting cushion.

    2. Install SST using the same procedure as for the rear suspension member front body mounting cushion (for LH Side).

      SST
      09570-24011
      09830-10010   ( 09830-01010, 09830-01020, 09830-01040, 09830-01050 )

      Note

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

    3. Using SST, install the rear suspension member front body mounting cushion until there is no clearance between the rear suspension member sub-assembly and rear suspension member front body mounting cushion.

      SST
      09570-24011
      09830-10010   ( 09830-01010, 09830-01020, 09830-01040, 09830-01050 )

      Note

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

      Tech Tips

      Perform the same procedure as for the rear suspension member front body mounting cushion (for LH Side).

    4. Remove SST from the rear suspension member sub-assembly.

  3. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION LH


    1. B006XI2C03
      *A Type A
      *B Type B
      *a View from Underneath
      B006Z38 Front of the Vehicle
      B006ZY0 Outside of the Vehicle

      Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion LH.

      Note


      • Position the rear suspension member rear body mount cushion LH in the correct direction.

      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion LH.

    2. B006YSDN01

      Install SST as shown in the illustration.

      SST
      09710-28031   ( 09711-02030, 09711-02040, 94622-51200 )
      09950-60021   ( 09951-00720, 09951-00890 )

      Note

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

    3. B00708SC03
      *a Hold
      B006ZFL Turn

      Using SST, install the rear suspension member rear body mount cushion LH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion LH.

      SST
      09710-28031   ( 09711-02030, 09711-02040, 94622-51200 )
      09950-60021   ( 09951-00720, 09951-00890 )

      Note

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

    4. Remove SST from the rear suspension member sub-assembly.

  4. INSTALL REAR SUSPENSION MEMBER REAR BODY MOUNT CUSHION RH


    1. B0070XTC02
      *A Type A
      *B Type B
      *a View from Underneath
      B006Z38 Front of the Vehicle
      B006ZY0 Outside of the Vehicle

      Confirm the installation direction and temporarily install a new rear suspension member rear body mount cushion RH.

      Note


      • Position the rear suspension member rear body mount cushion RH in the correct direction.

      • Do not apply lubricant to the outer sleeve of the rear suspension member rear body mount cushion RH.

    2. Install SST using the same procedure as for the rear suspension member rear body mount cushion LH.

      SST
      09710-28031   ( 09711-02030, 09711-02040, 94622-51200 )
      09950-60021   ( 09951-00720, 09951-00890 )

      Note

      Apply molybdenum grease to the threads and tip of the SST center bolt before use.

    3. Using SST, install the rear suspension member rear body mount cushion RH until there is no clearance between the rear suspension member sub-assembly and rear suspension member rear body mount cushion RH.

      SST
      09710-28031   ( 09711-02030, 09711-02040, 94622-51200 )
      09950-60021   ( 09951-00720, 09951-00890 )

      Note

      If the rear suspension member sub-assembly is scratched, apply paint to the scratched areas of the rear suspension member sub-assembly.

      Tech Tips

      Perform the same procedure as for the rear suspension member rear body mount cushion LH.

    4. Remove SST from the rear suspension member sub-assembly.

  5. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  6. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  7. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. Install the 4 rear suspension member cushions to the rear suspension member sub-assembly.

      Tech Tips

      When reusing the rear suspension member cushion, make sure to check its identification mark and install it to the correct position.

    2. B006ZDRC01
      *a Engine Lifter
      *b Attachment
      B006Y8C Attachment Placement Location

      Using an engine lifter and 4 attachments or equivalent tools, support the rear suspension member sub-assembly as shown in the illustration.

      CAUTION:

      B0070Q3

      • The rear suspension member sub-assembly is a very heavy component. Make sure that it is supported securely.

      • If the rear suspension member sub-assembly is not securely supported, it may drop, resulting in serious injury.

      Note


      • Use attachments or equivalent tools to keep the rear suspension member sub-assembly level.

      • Keep supporting the rear suspension member sub-assembly until the installation has been completed.

    3. Raise the rear suspension member sub-assembly until there is no clearance between the rear suspension member sub-assembly and vehicle.

    4. B006XB2N01

      Install the rear suspension member sub-assembly with the 2 rear suspension member lower stoppers, rear suspension member lower brace LH and rear suspension member lower brace RH, 2 bolts and 6 nuts.

      Torque:
      Bolt A
      158 N*m  { 1611 kgf*cm, 117 ft.*lbf }
      Nut B
      158 N*m  { 1611 kgf*cm, 117 ft.*lbf }
      Nut C
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  8. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH


    1. Temporarily install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt and nut.

      Note


      • Insert the bolt with the threaded end facing the rear of the vehicle.

      • Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  9. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  10. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  11. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  12. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  13. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  14. INSTALL REAR LOWER COIL SPRING INSULATOR LH

    Click here

  15. INSTALL REAR LOWER COIL SPRING INSULATOR RH

    Tech Tips

    Perform the same procedure as for the LH side.

  16. INSTALL REAR COIL SPRING LH

    Click here

  17. INSTALL REAR COIL SPRING RH

    Tech Tips

    Perform the same procedure as for the LH side.

  18. INSTALL REAR STABILIZER BAR

    Click here

  19. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

    Click here

  20. CONNECT REAR FLEXIBLE HOSE LH


    1. Connect the rear flexible hose LH to the rear flexible hose bracket with the bolt.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  21. CONNECT REAR FLEXIBLE HOSE RH

    Tech Tips

    Perform the same procedure as for the LH side.

  22. STABILIZE SUSPENSION

    Click here

  23. INSTALL REAR STABILIZER LINK ASSEMBLY LH

    Click here

  24. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  25. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  26. INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  27. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. Install the rear No. 2 suspension arm assembly LH (rear axle carrier sub-assembly side) with the bolt.

      Click here

  28. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  29. INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH


    1. Install the rear upper control arm assembly LH to the rear axle carrier sub-assembly LH with the bolt.

      Torque:
      73 N*m  { 744 kgf*cm, 54 ft.*lbf }

      Note

      Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

  30. INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  31. INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)

    Click here

  32. INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)

    Click here

  33. INSTALL CENTER EXHAUST PIPE ASSEMBLY

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here

  34. INSTALL REAR WHEEL

    Click here

  35. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. Install the rear No. 2 suspension arm assembly LH (rear suspension member sub-assembly side) with the nut.

      Click here

  36. INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  37. INSPECT FOR EXHAUST GAS LEAK

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here

  38. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  39. PERFORM INITIALIZATION

    Parking assist monitor system

    Click here for Initialization

    Click here for Calibration
    Lighting System (EXT) (w/ Automatic Headlight Beam Level Control System)

    Click here