REAR STABILIZER BAR INSTALLATION

PROCEDURE


  1. INSTALL REAR STABILIZER BUSHING


    1. Install the 2 rear stabilizer bushings to the rear stabilizer bar.

      Note

      Be sure to install the rear stabilizer bushings so that each cutout faces the front of the vehicle.

  2. INSTALL REAR NO. 1 STABILIZER BAR BRACKET


    1. B006WWBC01
      *a Arrow Mark
      B006ZY0 Front of the Vehicle

      Install the 2 rear No. 1 stabilizer bar brackets to the 2 rear stabilizer bushings.

      Note

      Be sure to install the rear No. 1 stabilizer bar brackets so that each arrow mark faces the front of the vehicle.

  3. INSTALL REAR STABILIZER BAR


    1. B006X76C01
      *a Identification Mark

      Install the rear stabilizer bar, 2 rear No. 1 stabilizer bar brackets and 2 rear stabilizer bushings to the rear suspension member sub-assembly with the 4 bolts.

      Torque:
      78 N*m  { 795 kgf*cm, 58 ft.*lbf }

      Note


      • Ensure that the identification mark faces the right side of the vehicle.

      • Temporarily tighten the bolt (A) and then fully tighten the 2 bolts in the order of (B) and (A).

  4. STABILIZE SUSPENSION

    Click here

  5. INSTALL REAR STABILIZER LINK ASSEMBLY LH


    1. B006XG5N03

      Install the rear stabilizer link assembly LH with the nut (A).

      Torque:
      75 N*m  { 765 kgf*cm, 55 ft.*lbf }

      Tech Tips

      If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

    2. Install the rear stabilizer link assembly LH with the bolt and nut (B).

      Torque:
      75 N*m  { 765 kgf*cm, 55 ft.*lbf }

      Note

      Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

  6. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Perform the same procedure as for the LH side.

  7. INSTALL CENTER EXHAUST PIPE ASSEMBLY

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here

  8. INSTALL NO. 1 FLOOR UNDER COVER (w/ Cover)


    1. B006X5ZN01

      Install the No. 1 floor under cover with the 2 grommets (B) and 2 clips (C).

      Torque:
      Grommet (B)
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Install the 2 bolts and clip (A).

      Torque:
      Bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  9. INSTALL NO. 2 FLOOR UNDER COVER (w/ Cover)


    1. B0070C6N01

      Install the No. 2 floor under cover with the 2 grommets (B) and 2 clips (C).

      Torque:
      Grommet (B)
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Install the 2 bolts and clip (A).

      Torque:
      Bolt
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

  10. INSTALL REAR WHEEL

    Click here

  11. INSPECT FOR EXHAUST GAS LEAK

    for 2AR-FE: Click here

    for A25A-FKS: Click here

    for 2GR-FKS: Click here