FRONT DRIVE SHAFT ASSEMBLY(for 2AR-FE) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT DRIVE SHAFT HOLE SNAP RING


    1. Install a new front drive shaft hole snap ring.

      Note

      Face the end gap of the front drive shaft hole snap ring downward.

  2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH


    1. Coat the splines of the front drive inboard joint assembly with ATF WS.

    2. Coat the snap ring of the front drive inboard joint assembly with MP grease.

    3. B006X41

      Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

      Note


      • Face the end gap of the front drive shaft hole snap ring downward.

      • Do not damage the front drive shaft oil seal LH.

      • Do not damage the front axle inboard joint boot.

      • Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.

      Tech Tips

      Confirm whether the drive shaft is securely driven in by checking the reaction force and sound.

    4. B006YRHC02
      B006Z38 Toyota Body Grease W

      Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

    5. B0071SYC01
      *a Matchmark

      Align the matchmarks and install the front drive shaft assembly LH to the front axle assembly.

      Note


      • Do not damage the front disc brake dust cover.

      • Do not damage the front axle outboard joint boot.

      • Check that there is no foreign matter on the deflector or contact surfaces.

      • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

      • Do not damage the deflector.

  3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH


    1. Install a new bearing bracket hole snap ring to the front drive shaft assembly RH.

    2. Coat the splines of the front drive inboard joint assembly with ATF WS.

    3. Align the inboard joint splines, and securely insert the front drive shaft assembly RH.

      Note


      • Do not damage the front drive shaft oil seal RH.

      • Do not damage the front axle inboard joint boot.

    4. B006XCU

      Install the bearing bracket hole snap ring and a new bolt.

      Torque:
      32.4 N*m  { 330 kgf*cm, 24 ft.*lbf }
    5. B00705AC01
      B006Z38 Toyota Body Grease W

      Apply 0.1 to 0.3 g (0.00353 to 0.0105 oz) of Toyota Body Grease W to each of the 4 areas shown in the illustration.

    6. B00711AC01
      *a Matchmark

      Align the matchmarks and install the front drive shaft assembly RH to the front axle assembly.

      Note


      • Do not damage the front disc brake dust cover.

      • Do not damage the front axle outboard joint boot.

      • Check that there is no foreign matter on the deflector or contact surfaces.

      • Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

      • Do not damage the deflector.

  4. CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

    Click here

  5. INSTALL FRONT STABILIZER LINK ASSEMBLY

    Click here

  6. CONNECT TIE ROD ASSEMBLY

    Click here

  7. INSTALL FRONT SPEED SENSOR

    Click here

  8. INSTALL FRONT AXLE SHAFT NUT


    1. Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

      Note


      • Make sure to perform this work even when using a new front drive shaft assembly.

      • Keep the threaded parts free of oil and foreign matter.

    2. B006ZVQ

      Using a 30 mm deep socket wrench, install the front axle shaft nut.

      Torque:
      294 N*m  { 2998 kgf*cm, 217 ft.*lbf }

      Tech Tips

      Depress the brake pedal to prevent the drive shaft from rotating.

    3. Using a chisel and hammer, stake the front axle shaft nut.

  9. ADD AUTOMATIC TRANSAXLE FLUID

    Click here

  10. INSTALL FRONT WHEELS

    Click here

  11. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

    Click here

  12. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  13. INSTALL FRONT FENDER APRON SEAL RH

    Click here

  14. CHECK FOR SPEED SENSOR SIGNAL

    Click here