FRONT DRIVE SHAFT ASSEMBLY(for 2AR-FE) COMPONENTS
ILLUSTRATION
| *1 | FRONT FENDER APRON SEAL LH | *2 | FRONT FENDER APRON SEAL RH |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | FRONT AXLE SHAFT NUT | *2 | FRONT DRIVE SHAFT ASSEMBLY |
| *3 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY | *4 | FRONT SPEED SENSOR |
| *5 | FRONT STABILIZER LINK ASSEMBLY | *6 | TIE ROD ASSEMBLY |
| *7 | FRONT AXLE ASSEMBLY | *8 | COTTER PIN |
| *9 | FRONT FLEXIBLE HOSE | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |  |
Toyota Body Grease W |
 |
Do not apply lubricants to the threaded parts | - | - |
ILLUSTRATION
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | FRONT DRIVE SHAFT HOLE SNAP RING | *4 | BEARING BRACKET HOLE SNAP RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease |  |
Toyota Genuine ATF WS |
ILLUSTRATION
| *A | for LH Side | - | - |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP |
| *3 | FRONT AXLE OUTBOARD JOINT BOOT | *4 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
| *5 | FRONT DRIVE INBOARD JOINT ASSEMBLY | *6 | FRONT DRIVE SHAFT DAMPER |
| *7 | FRONT DRIVE SHAFT DAMPER CLAMP | *8 | FRONT DRIVE SHAFT DUST COVER LH |
| *9 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP | *10 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP |
| *11 | SHAFT SNAP RING | *12 | TRIPOD JOINT |
| *13 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for RH Side | - | - |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP |
| *3 | FRONT AXLE OUTBOARD JOINT BOOT | *4 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP |
| *5 | FRONT DRIVE INBOARD JOINT ASSEMBLY | *6 | FRONT DRIVE SHAFT BEARING |
| *7 | FRONT DRIVE SHAFT DAMPER | *8 | FRONT DRIVE SHAFT DAMPER CLAMP |
| *9 | FRONT DRIVE SHAFT DUST COVER RH | *10 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP |
| *11 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP | *12 | SHAFT SNAP RING |
| *13 | TRIPOD JOINT | *14 | DRIVE SHAFT HOLE SNAP RING |
| *15 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY | - | - |
| ● | Non-reusable part | - | - |