Click here

EXHAUST PIPE REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front exhaust pipe assembly (TWC: Rear Catalyst), center exhaust pipe assembly and tail exhaust pipe assembly removal/installation are shown below.

Table 1. Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here
CAUTION:
B00719S

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

Click here

PROCEDURE


  1. Click here

    REMOVE TAIL EXHAUST PIPE ASSEMBLY

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


    1. B006XDX

      Remove the 2 bolts and disconnect the tail exhaust pipe assembly from the center exhaust pipe assembly.

    2. Remove the tail exhaust pipe assembly from the 2 exhaust pipe supports.

    3. Remove the gasket from the center exhaust pipe assembly.

  2. Click here

    REMOVE TAIL EXHAUST PIPE ASSEMBLY LH (for Dual Type)

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


    1. B0071SU

      Remove the 2 bolts and disconnect the tail exhaust pipe assembly LH from the center exhaust pipe assembly.

    2. Remove the tail exhaust pipe assembly LH from the 2 exhaust pipe supports.

    3. Remove the gasket from the center exhaust pipe assembly.

  3. Click here

    REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Single Type)

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


    1. B00711K

      Remove the 2 bolts, 2 compression springs and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).

    2. Remove the center exhaust pipe assembly from the exhaust pipe support.

    3. Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).

  4. Click here

    REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Dual Type)

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


    1. B0071NW

      Remove the 2 bolts, 2 compression springs and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst).

    2. Remove the center exhaust pipe assembly from the exhaust pipe support.

    3. Remove the gasket from the front exhaust pipe assembly (TWC: Rear Catalyst).

  5. Click here

    REMOVE FRONT CENTER FLOOR BRACE


    1. B006YYN

      Remove the 4 bolts and front center floor brace from the vehicle body.

  6. Click here

    REMOVE CENTER FLOOR CROSSMEMBER BRACE


    1. B006Y1G

      Remove the 4 bolts and center floor crossmember brace from the vehicle body.

  7. Click here

    REMOVE BODY MOUNTING PLATE


    1. B006XEO

      Remove the 6 bolts and body mounting plate.

  8. Click here

    REMOVE HEATED OXYGEN SENSOR

    Click here

  9. Click here

    REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)


    1. B0071NM

      Remove the 2 bolts, 2 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

    2. Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.

    3. Remove the gasket from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

  10. Click here

    REMOVE TAIL EXHAUST PIPE BAFFLE SUB-ASSEMBLY

    Tip:

    • Perform this procedure only when replacement of the tail exhaust pipe baffle sub-assembly is necessary.

    • If the tail exhaust pipe baffle sub-assembly is removed, replace it with a new one.

    • Use the same procedure as for the tail exhaust pipe assembly LH (for Dual Type).


    1. B0070KE

      Type A (w/ Tail Exhaust Pipe Baffle):


      1. Remove the tail exhaust pipe baffle sub-assembly.

    2. B006XEW

      Type B:


      1. Remove the tail exhaust pipe baffle sub-assembly.