Click here

CANISTER(w/ Canister Pump Module) REMOVAL

Click here
Click here

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during canister (charcoal canister assembly) removal/installation are shown below.

Table 1. Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Gas leak from exhaust system is repaired Inspection After Repair

  • Poor idle, etc.

  • Engine start function, etc.

Click here
Click here

PROCEDURE


  1. Click here

    REMOVE CENTER EXHAUST PIPE ASSEMBLY

    CAUTION:

    To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


    1. B004NIP

      Remove the 4 bolts and disconnect the center exhaust pipe assembly from the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly.

    2. Remove the center exhaust pipe assembly from the exhaust pipe support.

    3. Remove the 2 gaskets from the center exhaust pipe assembly and front exhaust pipe assembly (TWC: Rear Catalyst).

  2. Click here

    REMOVE REAR NO. 1 STABILIZER BAR BRACKET


    1. B004MAL

      Remove the 4 bolts and 2 rear No. 1 stabilizer bar brackets from the vehicle body.

  3. Click here

    REMOVE CANISTER (CHARCOAL CANISTER ASSEMBLY)


    1. B004O8BC01
      *1 Fuel Tank Vent Hose *2 Pipe (Canister (Charcoal Canister Assembly))
      *a Retainer *b Tab
      *c Tube Connector *d O-ring
      B006Z38 Pinch B006ZY0 Pull

      Disconnect the fuel tank vent hose from the canister (charcoal canister assembly).

      Note:

      • Remove any dirt or foreign matter on the tube connector before performing this work.

      • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

      • Perform this work by hand. Do not use any tools.

      • Do not forcibly bend, twist or turn the fuel tank vent hose.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the fuel tank vent hose.

      • If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.

      Tip:

      Do not remove the retainer.


      1. Pinch the tabs of the retainer to disengage the lock claws and pull it down.

      2. Pull off the fuel tank vent hose.

    2. B004NFFC01
      *1 Vent Line Hose *2 Pipe (Canister (Charcoal Canister Assembly))
      *a Retainer *b Tab
      *c Tube Connector *d O-ring
      B006Z38 Pinch B006ZY0 Pull

      Disconnect the vent line hose from the canister (charcoal canister assembly).

      Note:

      • Remove any dirt or foreign matter on the tube connector before performing this work.

      • Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the tube connector has an O-ring that seals the pipe (canister (charcoal canister assembly)).

      • Perform this work by hand. Do not use any tools.

      • Do not forcibly bend, twist or turn the vent line hose.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the vent line hose.

      • If the tube connector and pipe (canister (charcoal canister assembly)) are stuck, push and pull to release them.

      Tip:

      Do not remove the retainer.


      1. Pinch the tabs of the retainer to disengage the lock claws and pull it down.

      2. Pull off the vent line hose.

    3. B004N81

      Slide the clip and disconnect the purge line hose from the canister (charcoal canister assembly).

    4. B004OCXC01
      B006Z38 Bolt
      B006ZY0 Clip

      Remove the 2 bolts.

    5. Disengage the clip from the canister (charcoal canister assembly).

    6. B004HVK

      Disengage the claw and remove the canister (charcoal canister assembly) from vehicle body as shown in the illustration.

    7. B004LDQ

      Remove the clip from the vehicle body.

  4. Click here

    REMOVE NO. 2 CHARCOAL CANISTER SUB-ASSEMBLY


    1. B004IKCC01
      *1 Air Line Tube
      *2 Pipe (Leak Detection Pump Sub-assembly)
      *a Tube Connector
      *b O-ring
      B006Z38 Pinch
      B006ZY0 Pull off

      Disconnect the air line tube from the leak detection pump sub-assembly.

      Note:

      • Remove any dirt or foreign matter on the tube connector before performing this work.

      • Perform this work by hand. Do not use any tools.

      • Do not forcibly bend, twist or turn the air line tube.

      • Protect the disconnected parts by covering them with plastic bags after disconnecting the air line tube.

      • If the tube connector and pipe (leak detection pump sub-assembly) are stuck, push and pull to release them.


      1. Push the air line tube firmly toward the leak detection pump sub-assembly.

      2. Pinch the tube connector as shown in the illustration.

      3. Pull off the air line tube from the pipe (leak detection pump sub-assembly).

    2. B004HPP

      Disconnect the leak detection pump sub-assembly connector.

    3. B004KUD

      Remove the 3 nuts and No. 2 charcoal canister sub-assembly from the vehicle body.

  5. Click here

    REMOVE LEAK DETECTION PUMP SUB-ASSEMBLY

    Tip:

    Only perform this procedure when replacement of the leak detection pump sub-assembly is necessary.


    1. Before removing the leak detection pump sub-assembly, clean the No. 2 charcoal canister sub-assembly by blowing air into it to ensure that the No. 2 charcoal canister sub-assembly is free of foreign matter.

      Note:

      • Make sure to clean the No. 2 charcoal canister sub-assembly using air only.

      • Do not use gasoline, thinners or solvents.

    2. B004MIPC01
      *a Protective Tape

      While disengaging the 2 claws as shown in the illustration, push the leak detection pump sub-assembly upwards using a screwdriver with its tip wrapped with protective tape to remove it.

    3. Check if the No. 2 charcoal canister sub-assembly contains foreign matter such as mud or water.


      1. B004IIG

        Visually check that the inside of the No. 2 charcoal canister sub-assembly is free of foreign matter.

      2. Hold the No. 2 charcoal canister sub-assembly upside down to make sure that it is free of foreign matter.

        If the No. 2 charcoal canister sub-assembly contains foreign matter, replace it.