ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *1 | FRONT FENDER APRON SEAL LH | *2 | FRONT FENDER APRON SEAL RH |
| *3 | FRONT LOWER BUMPER ABSORBER | *4 | FRONT WHEEL OPENING EXTENSION PAD LH |
| *5 | FRONT WHEEL OPENING EXTENSION PAD RH | *6 | NO. 1 ENGINE UNDER COVER |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE | *2 | INLET AIR CLEANER ASSEMBLY |
| *3 | BATTERY | *4 | BATTERY CLAMP SUB-ASSEMBLY |
| *5 | ECM | *6 | V-BANK COVER SUB-ASSEMBLY |
| *7 | NO. 2 BATTERY CLAMP | *8 | NO. 2 VENTILATION HOSE |
| *9 | MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR | *10 | VACUUM HOSE |
| *11 | NO. 1 FUEL VAPOR FEED HOSE | *12 | ENGINE ROOM MAIN WIRE |
| *13 | EARTH WIRE | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | INLET HEATER WATER HOSE | *2 | NO. 1 COOLER REFRIGERANT DISCHARGE HOSE SUB-ASSEMBLY |
| *3 | NO. 1 FUEL HOSE | *4 | NO. 1 FUEL VAPOR FEED HOSE |
| *5 | NO. 2 RADIATOR HOSE | *6 | OUTLET HEATER WATER HOSE |
| *7 | RADIATOR HOSE SUB-ASSEMBLY | *8 | SUCTION HOSE SUB-ASSEMBLY |
| *9 | TRANSMISSION CONTROL CABLE ASSEMBLY | *10 | UNION TO CHECK VALVE HOSE |
| *11 | NO. 1 FUEL PIPE CLAMP | *12 | O-RING |
| *13 | RADIATOR RESERVE TANK ASSEMBLY | *14 | NO. 2 FUEL PIPE CLAMP |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY WITH TRANSAXLE | *2 | FRONT FRAME ASSEMBLY |
| *3 | REAR ENGINE MOUNTING INSULATOR | *4 | WIRE HARNESS |
| *5 | VACUUM HOSE | *6 | NO. 1 WATER BY-PASS HOSE |
| *7 | WATER BY-PASS HOSE ASSEMBLY | *8 | TRANSMISSION BREATHER CLAMP |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
ILLUSTRATION
| *1 | ENGINE ASSEMBLY WITH TRANSAXLE | *2 | ENGINE MOUNTING BRACKET SUB-ASSEMBLY LH |
| *3 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH | *4 | ENGINE MOUNTING SPACER |
| *5 | ENGINE WIRE | *6 | FRONT ENGINE MOUNTING INSULATOR |
| *7 | FRONT FRAME ASSEMBLY | *8 | ENGINE MOUNTING INSULATOR LH |
| *9 | STEERING INTERMEDIATE SHAFT ASSEMBLY | *10 | FRONT BUMPER EXTENSION SUB-ASSEMBLY RH |
| *11 | FRONT BUMPER EXTENSION SUB-ASSEMBLY LH | *12 | FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY RH |
| *13 | FRONT SUSPENSION MEMBER BRACKET SUB-ASSEMBLY LH | *14 | NO. 2 RELAY BLOCK COVER |
| *15 | NO. 2 ENGINE MOUNTING STAY RH | - | - |
 |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
ILLUSTRATION
| *1 | AUTOMATIC TRANSAXLE ASSEMBLY | *2 | FRONT ENGINE MOUNTING BRACKET |
| *3 | BREATHER PLUG HOSE | *4 | BREATHER PLUG SUB-ASSEMBLY |
| *5 | NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Upper Side) | *6 | STARTER ASSEMBLY |
| *7 | REAR DRIVE PLATE SPACER | *8 | NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
| *9 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY | *10 | FLYWHEEL HOUSING UNDER COVER |
| *11 | DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT | - | - |
| *a | BLACK COLOR: x 1 SILVER COLOR: x 5 |
- | - |
| |
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping": N*m (kgf*cm, ft.*lbf) | |
N*m (kgf*cm, ft.*lbf): Specified torque |
| |
Adhesive 1324 | ★ | Precoated part |