CYLINDER HEAD GASKET INSTALLATION

CAUTION / NOTICE / HINT

PROCEDURE

1. INSTALL CYLINDER HEAD GASKET

   
   

   1. Clean the cylinder block sub-assembly and cylinder head sub-assembly with solvent.

   2. 

      *a	Lot No.
      	Front of Engine

      Place a new cylinder head gasket on the cylinder block sub-assembly with the Lot No. stamp facing upward.

      Note

      Make sure that the cylinder head gasket is installed in the correct orientation.

2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

   Click here

3. INSTALL NO. 2 CAMSHAFT

   Click here

4. INSTALL CAMSHAFT

   Click here

5. INSTALL CAMSHAFT BEARING CAP

   Click here

6. INSTALL VALVE STEM CAP

   Click here

7. INSTALL VALVE LASH ADJUSTER ASSEMBLY

   Click here

8. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

   Click here

9. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

   Click here

10. INSTALL FUEL PUMP LIFTER GUIDE

    Click here

11. INSTALL TIMING CHAIN COVER ASSEMBLY

    Click here

12. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

    Click here

13. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

    Click here

14. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

    Click here

15. INSTALL NO. 1 CHAIN VIBRATION DAMPER

    Click here

16. INSTALL CHAIN SUB-ASSEMBLY

    Click here

17. INSTALL CHAIN TENSIONER SLIPPER

    Click here

18. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

    Click here

19. INSTALL OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

    Click here

20. SET NO. 1 CYLINDER TO TDC (COMPRESSION)

    Click here

21. INSTALL NO. 2 TIMING GEAR COVER ASSEMBLY

    Click here

22. INSTALL TIMING CHAIN COVER OIL SEAL

    Click here

23. INSTALL SPARK PLUG TUBE GASKET

    Click here

24. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

25. INSTALL OUTLET WATER BY-PASS SUB-ASSEMBLY

    Click here

26. INSTALL WATER OUTLET

    Click here

27. INSTALL CRANKSHAFT PULLEY ASSEMBLY

    Click here

28. INSTALL VACUUM PUMP ASSEMBLY

    Click here

29. INSTALL CAM TIMING CONTROL MOTOR O-RING

    Click here

30. INSTALL CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

    Click here

31. INSTALL CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

    Click here

32. INSTALL OIL PRESSURE CONTROL VALVE ASSEMBLY

    Click here

33. INSTALL PURGE VALVE (PURGE VSV)

    Click here

34. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

35. INSTALL IGNITION COIL ASSEMBLY

    Click here

36. INSTALL FUEL INJECTOR SEAL

    Click here

37. INSTALL DIRECT FUEL INJECTOR ASSEMBLY

    Click here

38. INSTALL FUEL DELIVERY PIPE

    Click here

39. INSTALL PORT FUEL INJECTOR ASSEMBLY

    Click here

40. INSTALL NO. 5 ENGINE WIRE

    Click here

41. INSTALL INJECTOR VIBRATION INSULATOR

    Click here

42. INSTALL NO. 1 DELIVERY PIPE SPACER

    Click here

43. INSTALL FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

    Click here

44. INSTALL NO. 7 WATER BY-PASS HOSE

    Click here

45. TEMPORARILY INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

    Click here

46. TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

47. INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

    Click here

48. INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

    Click here

49. CONNECT FUEL TUBE SUB-ASSEMBLY

    Click here

50. INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

    Click here

51. INSTALL INTAKE MANIFOLD

    Click here

52. INSTALL NO. 2 WATER BY-PASS PIPE

    Click here

53. INSTALL NO. 3 WATER BY-PASS PIPE

    Click here

54. INSTALL EGR VALVE ASSEMBLY

    Click here

55. INSTALL WATER HOSE CONNECTOR

    Click here

56. INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

    Click here

57. INSTALL NO. 1 EGR COOLER BRACKET

    Click here

58. INSTALL EGR COOLER ASSEMBLY

    Click here

59. INSTALL THROTTLE BODY GASKET

    Click here

60. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Click here

61. INSTALL EXHAUST MANIFOLD (TWC: Front Catalyst)

    Click here

62. INSTALL MANIFOLD STAY

    Click here

63. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

64. INSTALL FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)

    Click here

65. INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

    Click here

66. INSTALL NO. 3 TIMING CHAIN COVER

    Click here

67. INSTALL TIMING GEAR COVER INSULATOR

    Click here

68. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

69. INSTALL NO. 2 ENGINE COVER

    Click here

70. INSTALL COMPRESSOR ASSEMBLY WITH PULLEY

    Click here

71. INSTALL GENERATOR ASSEMBLY

    Click here

72. INSTALL V-RIBBED BELT

    Click here

73. INSTALL ENGINE HANGERS

    Click here

74. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

    Click here