Click here

SFI SYSTEM(w/ Canister Pump Module), Diagnostic DTC:P261401

Click here
Click here
DTC Code DTC Name
P261401 Camshaft Position Signal Output "A" General Electrical Failure
Click here

DESCRIPTION

Refer to DTC P001001.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P261401 Camshaft Position Signal Output "A" General Electrical Failure Malfunction in rotation sensor of cam timing control motor with EDU assembly is detected for 3 seconds (1 trip detection logic).

  • Cam timing control motor with EDU assembly

  • ECM

 Comes on DTC stored SAE Code: P2614
Table 1. Symptoms and Fail-safe Operation During Camshaft Control Motor Malfunction
Vehicle Condition Fail-Safe

  • Engine difficult to start

  • Lack of power

 The cam timing control motor with EDU assembly is operated to the most retarded position.
Click here

MONITOR DESCRIPTION

This DTC is output when a malfunction in the cam timing control motor rotation sensor is detected. The cam timing control motor with EDU assembly is equipped with a self diagnostic function, which is used to output diagnosis signals (VTM) to the ECM. If the ECM receives a duty signal of 40%, this DTC is output immediately (1 trip detection logic).

Click here

MONITOR STRATEGY

Required sensor/Components Cam timing control motor with EDU assembly
Frequency of Operation Continuous
Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the GTS on.

  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  5. Turn the engine switch off and wait for at least 30 seconds.

  6. Start the engine.

  7. Idle the engine for 10 seconds or more [A].

  8. Turn the GTS on.

  9. Enter the following menus: Powertrain / Engine / Trouble Codes [B].

  10. Read the DTCs.

    Tip:

    • If a DTC is output, the system is malfunctioning.

    • If a DTC is not output, perform the following procedure.

  11. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

  12. Input the DTC: P261401.

  13. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    Tip:

    • If the judgment result is NORMAL, the system is normal.

    • If the judgment result is ABNORMAL, the system has a malfunction.

    • If the judgment result is INCOMPLETE, perform steps [A] through [B] again.

Click here

CAUTION / NOTICE / HINT

Tip:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    REPLACE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY


    1. Replace the cam timing control motor with EDU assembly.

      Click here

      Tip:

      Perform "Inspection After Repair" after replacing the cam timing control motor with EDU assembly.

      Click here

      Result
      Proceed to
      NEXT

  2. Click here

    CLEAR DTC


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the GTS on.

    4. Clear the DTCs.


      1. Powertrain > Engine > Clear DTCs


    5. Turn the engine switch off and wait for at least 30 seconds.

      Result
      Proceed to
      NEXT

  3. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

    2. Enter the following menus: Powertrain / Engine / Trouble Codes.

    3. Read the DTCs.


      1. Powertrain > Engine > Trouble Codes


      Result
      Result Proceed to
      DTCs are not output A
      DTC P261401 is output B